manualshive.com logo in svg

Shinko AER-101-ORP, Instruction Manual, Page: 38 / 84

Share
Download
Shinko AER-101-ORP Instruction Manual Download Page 38

38

Character

Setting Item, Function, Setting Range

Factory Default

Output OFF time when EVT3 output ON

0 sec.

• Sets Output OFF time when EVT3 output is ON.

If ON time and OFF time are set, EVT3 output can be turned ON/OFF
in a configured cycle when EVT3 output is turned ON.( Fig 7.5-2, p.40)

• Available when

(ORP input low limit action) or

(ORP input high limit action) is selected in [EVT3 type].

• Not available for P control action
• Setting range: 0 to 10000 sec.

EVT3 ORP input error alarm EVT

type

No action

• Selects EVT

output type (except EVT3 type) in order to assess

EVT3 ORP input error alarm.

• Available only when

(ORP input error alarm output) is

selected in [EVT3 type]

•

: EVT1 action
: EVT2 action
: No action
: EVT4 action

EVT3 ORP input error alarm span
when EVT

output ON

0 mV

• Sets span to assess EVT3 ORP input error alarm when EVT

output

(selected in [EVT3 ORP input error alarm EVT

type]) is ON.

• Available only when

(ORP input error alarm output) is

selected in [EVT3 type]

• Setting range: 0 to 2000 mV

When set to 0 (zero), ORP input error alarm is disabled.

EVT3 ORP input error alarm time
when EVT

output ON

0 sec.

• Sets time to assess EVT3 ORP input error alarm when EVT

output

(selected in [EVT3 ORP input error alarm EVT

type]) is ON.

• Available only when

(ORP input error alarm output) is

selected in [EVT3 type]

• Setting range: 0 to 10000 seconds or minutes

(*)

When set to 0 (zero), ORP input error alarm is disabled.

(*) Time unit follows the selection in [ORP input error alarm time unit].

Summary of Contents for AER-101-ORP





















































































Reviews:

No comments