Shinko AER-101-ORP Instruction Manual Download Page 36

Page: 36 / 84

Character

Setting Item, Function, Setting Range

Factory Default

EVT3 hysteresis type

Reference Value

• Selects EVT3 output hysteresis type (Medium or Reference Value).

(Fig 7.5-1, p.40)

• Available when

(ORP input low limit action) or

(ORP input high limit action) is selected in [EVT3 type].

• Not available for the P control action.
•

: Medium Value

Sets the same value for both ON and OFF sides in
relation to EVT3 value.
Only ON side needs to be set.

: Reference Value

Sets individual values for ON and OFF sides in relation
to EVT3 value.

Both ON and OFF sides need to be set individually.

EVT3 ON side

10 mV

• Sets the span of EVT3 ON side. (Fig 7.5-1, p.40)

(Medium Value) is selected in [EVT3 hysteresis type], the

span of ON/OFF side will be the same value.

• Available when

(ORP input low limit action) or

(ORP input high limit action) is selected in [EVT3 type].

• Not available for the P control action.
• Setting range: 0 to 200 mV

EVT3 OFF side

10 mV

• Sets the span of EVT3 OFF side. (Fig 7.5-1, p.40)
• Available when

(ORP input low limit action) or

(ORP input high limit action) is selected in [EVT3 type].

• Not available for the P control action, or if

(Medium Value)

is selected in [EVT3 hysteresis type].

• Setting range: 0 to 200 mV

EVT3 ON delay time

0 sec.

• Sets EVT3 delay time.

The EVT3 output does not turn ON after the input value exceeds the
EVT3 value until the time set in [EVT3 ON delay time] elapses.

• Available when

(ORP input low limit action) or

(ORP input high limit action) is selected in [EVT3 type].

• Not available for the P control action.
• Setting range: 0 to 10000 sec.

Summary of Contents for AER-101-ORP





















































































Search results

Summary of Contents for AER-101-ORP

Reviews:

Related manuals for AER-101-ORP

Brands by name

Popular brands

Shinko AER-101-ORP, Instruction Manual

Search results

Summary of Contents for AER-101-ORP

Reviews:

Related manuals for AER-101-ORP

Brands by name

Popular brands