Sheriff ZX-1060, Manual Of Installation And Use

Page: 42 / 75

ShenZhen YH Innovative Technology, Inc.
42
42 42
42
Choice Choice Choice Choice of of of of condition condition condition condition (of (of (of (of time) time) time) time) of of of of working working working working starter starter starter starter at at at at starting starting starting starting of of of of the the the the engine engine engine engine
(function (function (function (function SF8) SF8) SF8) SF8)
For right choice of the condition of working starter serve programmable function SF8.
Attention! Attention! Attention! Attention!
System confirms the fact of start of the engine by signal of tachometer or by appearance of voltage of charging of
storage cell according to installed parameter to SF7. For some name plates of the cars the signals of confirmative
start of the engine may appear with delay that may go to “torsion” of starter by running engine. Urgently we
commend to choose that condition of working starter which comes near to your car maximally.
Programmable
Programmable Programmable
Programmable delay
delay delay
delay of
of of
of starter
starter starter
starter (start
(start (start
(start of
of of
of diesel)
diesel) diesel)
diesel) (function
(function (function
(function SF10)
SF10) SF10)
SF10)
For accomplishment of preparative operation of side electronics of the car for start of the engine the starter is
turned on with delay. Especially these concerns about the car with diesel engine. SF10 helps to install time of
delay of starter optimally or to synchronize starter by preparedness of checking lamp of heating the fuel of nozzle
of diesel engine.
Check
Check Check
Check the
the the
the start
start start
start of
of of
of the
the the
the engine
engine engine
engine by
by by
by signal
signal signal
signal of
of of
of tachometer
tachometer tachometer
tachometer (function
(function (function
(function SF7.1)
SF7.1) SF7.1)
SF7.1)
Program idling turnovers before use the auto run of the engine.
System ZX-1060 provides checking the start of the engine by signal of tachometer. Start of the engine will be
stopped, if accounted turnovers of the engine exceed the value 4xN
xx
turnovers/minute. System ZX-1060
provides checking the turnovers of the engine in condition it work. The engine will stopped immediately in the
event of that if actual turnovers of the engine exceed the value 4xN
xx
turnovers/minute. Corresponding error will
be recorded to memory of the errors of automatic start.
Programmable
Programmable Programmable
Programmable idle
idle idle
idle turnovers
turnovers turnovers
turnovers of
of of
of the
the the
the engine
engine engine
engine
1.
Transfer the switch “AST” to condition “OFF”.
2.
Turn on the ignition or wind the engine.
3.
During 10 seconds switch “AST” to condition “ON/OFF” three times.
4.
In the event of achievement dimension lights flash one time, siren whistles one time, confirming successful
SF8
SF8.1 (2/4/8 seconds)
SF8.2 (0.6/0.6/0.6 seconds)
SF8.3 (0.8/0.8/0.8 seconds)
SF8.4 (1/1/1 second)
SF8.5 (1.5/1.5/1.5 second)
SF8.6 (2/2/2 seconds)
-permit to give time of rolling starter in condition of three attempting of start of
the engine.
-provide progressive amplification of time of rolling starter with every
attempting correspondingly.
–maximal time of rolling starter 0.6 second in all attempting
–maximal time of rolling starter 0.8 second in all attempting
-maximal time of rolling starter 1 second in all attempting
-maximal time of rolling starter 1.5 second in all attempting
-maximal time of rolling starter 2 seconds in all attempting
System terminates rolling starter automatically until expiration of maximal time,
if the engine is started.