ShenZhen YH Innovative Technology, Inc.
12
12
12
12
Function
Function
Function
Function
Description
Description
Description
Description of
of
of
of actions
actions
actions
actions
For
For
For
For example:
example:
example:
example:
activated cyclic timer.
System indicated interval
2:00.
Simultaneously pressed buttons 1+4 (Arm+ch3)-system
changed intervals and indicated on screen 3:00.
Following
pressing against the buttons 1+4 (Arm+ch3) changes interval to
4:00, afterwards 1:00 and by circle.
System automatic leaves out of procedure if during 10 seconds does
not accomplish actions by change of intervals.
Turning on/turning off
the engine by sensor
of
temperature/procedur
e
of
change
of
temperature of start of
engine
Twice
Twice
Two
Two
Two
Two simultaneous
simultaneous
simultaneous
simultaneous short
short
short
short pressings
pressings
pressings
pressings against
against
against
against the
the
the
the buttons
buttons
buttons
buttons 1+3
1+3
1+3
1+3
during
during
during
during 2
2
2
2 seconds,
seconds,
seconds,
seconds, at
at
at
at installed
installed
installed
installed temperature
temperature
temperature
temperature in
in
in
in function
function
function
function SF6.
SF6.
SF6.
SF6.
System confirms activation of timer by turning on of icon
“thermometer” on screen of trinket-transmitter, also, during 3
seconds, indicates earlier installed temperature of start of engine.
During following 10 seconds it may enter the procedure of cyclic
change of value of temperature of start in every momentary
simultaneous pressing against the buttons 1+4 (Arm+ch3).
Every
pressing will sequentially install new value of temperature with its
indication on screen of trinket-transmitter of two-way contact at
acceptance of relevant signal from basic block.
System automatic leaves out of procedure if during 10 seconds do
not accomplish actions by change of parameters.
For
For
For
For example:
example:
example:
example:
activated start by temperature.
System indicated
temperature -10
℃
.
Simultaneously pressed buttons 1+4
(Arm+ch3)-system changed indication of temperature on screen -
15
℃
.
Following pressing against the buttons 1+4 (Arm+ch3)
changes value of temperature to -20
℃
, afte5
℃
and by
circle.
System automatic leaves out of procedure if during 10
seconds do not accomplish actions by change of parameter.
Emergency
disconnection
of
condition
of “turbo
timer” in condition:
manual gear-box or
automatic
Twice
Twice
Two
Two
Two
Two short
short
short
short pressings
pressings
pressings
pressings against
against
against
against the
the
the
the button
button
button
button 3(6)
3(6)
3(6)
3(6) during
during
during
during 2
2
2
2 seconds
seconds
seconds
seconds
(see
(see
(see
(see picture
picture
picture
picture 1),
1),
1),
1), if
if
if
if function
function
function
function SF2
SF2
SF2
SF2 is
is
is
is turned
turned
turned
turned on.
on.
on.
on.
Reset of active condition of turbo timer with the help of transmitter.
1.
Take out the key from lock of ignition of car.
2.
During 2 seconds twice presses the button 3 (6).
3.
System must give up the channel of turbo timer without
delivery of audio signal.
Turbo timer may turn off by command only from trinket-
transmitter.
Start/stop
of
engine/turn
on
the
procedure of change
of time of working
engine
Twice
Twice
Two
Two
Two
Two short
short
short
short pressings
pressings
pressings
pressings against
against
against
against the
the
the
the button
button
button
button 6
6
6
6 during
during
during
during 2
2
2
2 seconds
seconds
seconds
seconds (see
(see
(see
(see
picture
picture
picture
picture 1).
1).
1).
1).
System starts engine, if conditions of start are accomplished (see
description of “remote start of engine”).
During following 10 seconds after successful start of engine it may
enter the procedure of cyclic change of interval of time of automatic
work of engine in every momentary simultaneous pressing against
the buttons 1+4 (Arm+ch3).
Every pressing will sequentially
install new value of time of automatic work of engine with its
indication on screen of trinket-transmitter of two-way contact in
acceptance of relevant signal from basic block.
System automatic
leaves out of procedure, if during 10 seconds do not accomplish
actions by change of parameter.
For
For
For
For eeeexample:
xample:
xample:
xample:
remotely started engine.
System indicated interval
of time 0:10.
Simultaneously pressed buttons 1+4 (Arm+ch3)-
system changed interval and indicated on screen 0:15, following
pressing of buttons 1+4 (ARM+ch3) change interval to 0:20,
afterwards 0:25 and so on by circle 0:25, 0:30, -:--, 0:10…
System automatically leaves the procedure, if during 10 seconds
does not accomplish actions by changing parameter.
