Shel lab BACTRON300 Installation And Operation Manual Download Page 81 | Manualshive

Page: 81 / 86

Shel lab BACTRON300 Installation And Operation Manual Download Page 81

81 |

P a g e

ACCESSORIES

Shel Lab offers the following BACTRON accessories for sale. Please see our website for prices

.

Activated Carbon Media (2 lbs / 0.9 kgs)

For scrubbing hydrogen sulfides, fatty acids, and some toxic or
corrosive compounds from the workstation atmosphere.

Part Number 1060500

Activated Carbon, Volatile Compounds Scrubber Fan

Holds activated carbon scrubber media. Significantly speeds the
removal of sulfides, fatty acids, and toxic or corrosive compounds.

Part Number 9490578 (For 110

– 120 volt units)

Acrylic Glass Cleaner (2oz / 59.2ml)

Novus brand acrylic glass cleaner.

Part Number 1060503

Acrylic Glass Scratch Remover (2oz / 59.2ml)

Helps remove visible scratches and nicks from acrylic glass.

Part Number 1060504

Anaerobic Chamber Start-Up Kit

Includes a spare 12 X 12 pass box door gasket, carbon volatile
compounds scrubber media, chamber cleaner (benzalkonium chloride
solution), Novus acrylic glass cleaner and scratch remover, 10 Oxoid
brand anaerobic indicator strips, 2 sets of spare latex cuffs, and a spare
sleeve O-ring.

Part Number 9490511

Anaerobic Indicator Strips

A box of 100 Oxoid anaerobic indicator strips.

Part Number 9900706

«
...
79
80
81
82
83
...
»

Summary of Contents for BACTRON300























































































Reviews:

No comments