Sharp UX-B700 Operation Manual Download

Page: 45 / 114

Sending a Fax by Automatic Dialling

2. Send

ing

Load the document(s).

•

If desired, press

to set

the resolution and/or contrast.

Press the Rapid Key corresponding to
the desired Speed Dial number.

•

The name of the receiving party will
appear in the display. If no name was
stored, the fax number will appear. (If
the name or number is incorrect, press

•

The document will be automatically
transmitted once the connection is
established.

•

If the transmission is completed successfully, the machine will beep once.

•

If an error occurs, the machine will beep three times and print a Transaction
Report to inform you of the problem (see page 86).

Using a Rapid Key for a voice call

To use a Rapid Key for a voice call, simply lift the handset and then press the
Rapid Key.

RESOLUTION/

RECEPTION MODE

STOP

Example: To dial Speed
Dial number 01, press
Rapid Key 01.

Rapid Key Dialling

If the number you want to dial has been stored as a Speed Dial number from
01 to 18, you can dial it by pressing the corresponding Rapid Key.

READY TO SEND

all.book Page 43 Friday, April 1, 2005 9:53 AM

Summary of Contents for UX-B700



















































































































Search results

Summary of Contents for UX-B700

Reviews:

Related manuals for UX-B700

Brands by name

Popular brands

Sharp UX-B700, Operation Manual

Search results

Summary of Contents for UX-B700

Reviews:

Related manuals for UX-B700

Brands by name

Popular brands