Sharp UX-B700 Operation Manual Download Page 68

Page: 68 / 114

5. Answering Machine Connection

Connecting an Answering Machine

If desired, you can connect an answering machine to your fax machine's

TEL.

SET

socket This will allow you to receive both voice messages and faxes

when you are out.

♦

Important:

If the answering machine is not connected to the

TEL. SET

socket on the fax as shown, the setup will not operate properly.

Remove the seal covering the TEL.
SET socket.

Connect the answering machine's telephone line socket to the TEL. SET
socket using the provided adapter.

•

Eire:

Insert the answering machine’s telephone line directly into the

TEL. SET

socket.

TEL.LINE

TEL.SET

TEL.L

INE

TEL.SE

To answering machine's
telephone line socket.

Make sure the

TEL. LINE

socket

is connected to the
wall socket.

all.book Page 66 Friday, April 1, 2005 9:53 AM

Summary of Contents for UX-B700



















































































































Search results

Summary of Contents for UX-B700

Reviews:

Related manuals for UX-B700

Brands by name

Popular brands

Sharp UX-B700, Operation Manual

Search results

Summary of Contents for UX-B700

Reviews:

Related manuals for UX-B700

Brands by name

Popular brands