Sharp UX-B700 Operation Manual Download Page 47

Page: 47 / 114

Sending a Fax by Automatic Dialling

2. Send

ing

Searching for an auto-dial number

If you don’t remember the Rapid Key or Speed Dial number in which you have
stored a full fax or phone number, follow these steps to search for the number.

If you are sending a fax, load the

document(s).

•

If desired, press

to set

the resolution and/or contrast.

Press

(or

) until the name of the other party appears in the

display (if no name was stored, the number will appear).

If you are sending a fax, press

. Dialling and transmission begins.

•

If the transmission is completed successfully, the machine will beep once.

•

If an error occurs, the machine will beep three times and print a Transaction
Report to inform you of the problem (see page 86).

If you are making a phone call, lift the handset. Dialling begins. (If you

lifted the handset before searching for the number, press

begin dialling.)

RESOLUTION/

RECEPTION MODE

REDIAL

START/

MEMORY

START/

MEMORY

READY TO SEND

all.book Page 45 Friday, April 1, 2005 9:53 AM

Summary of Contents for UX-B700



















































































































Search results

Summary of Contents for UX-B700

Reviews:

Related manuals for UX-B700

Brands by name

Popular brands

Sharp UX-B700, Operation Manual

Search results

Summary of Contents for UX-B700

Reviews:

Related manuals for UX-B700

Brands by name

Popular brands