Sharp UX-B700 Operation Manual Download Page 15

Page: 15 / 114

Loading Printing Paper

1. Installation

Pull the paper plate toward you, and
remove the paper tray cover from the
paper tray.

Pull the paper plate toward you and insert the stack of paper into the
tray,

PRINT SIDE UP.

•

If paper remains in the tray, take it out and combine it into a single stack
with the new paper.

Pull the paper plate toward you and
replace the paper tray cover.

Loading Printing Paper

You can load up to 200 sheets of A4-size, 60 - 80 g/m

paper in the paper tray

(at room temperature; maximum stack height should not be higher than the
line on the tray).

The stack should
not be higher
than this line

Be sure to load the paper so that
printing takes place on the

print

side

of the paper. Printing on the reverse
side may result in poor print quality.

all.book Page 13 Friday, April 1, 2005 9:53 AM

Summary of Contents for UX-B700



















































































































Search results

Summary of Contents for UX-B700

Reviews:

Related manuals for UX-B700

Brands by name

Popular brands

Sharp UX-B700, Operation Manual

Search results

Summary of Contents for UX-B700

Reviews:

Related manuals for UX-B700

Brands by name

Popular brands