R-D219G
E-11
E-12
OTHER CONVENIENT FEATURES
You can adjust cooking results for AUTO (Reheat) and
Defrost as you like.
Should you discover that you like the automatic
settings slightly more done, press MORE once within
10 sec. after pressing START.
The display will show “ ”.
Should you discover that you like any automatic
settings slightly less done, press LESS once within
10 sec. after pressing START.
While “ ” is flashing, you can change the setting.
Automatic Cooking Time Adjustment
(More or Less Time Adjustment)
End of Cooking Reminder
At end of cooking, the oven will signal and repeat after
1, 2 and 3 minutes unless door is opened or
STOP/
CLEAR is pressed.
Mute the Oven
To mute the oven, make sure the initial display is
shown and press DONABE for 4 sec. until the 2 short
beeps sound. Then press STOP/CLEAR.
NOTES:
1. The oven will hold the setting even if the power is
interrupted.
2. The following 2 signals will sound even if the oven
is in the mute setting.
- Error sound
- Cancelation sound during oven operation
3. To restore the sound, press DONABE for 4 sec. until
a short beep sounds. Then press
STOP/CLEAR.
The display will show “ ”.
If no pad is pressed within 10 sec, the standard
setting will be selected automatically.
TROUBLESHOOTING
If “C with number” is displayed or you think the oven is not working properly, check the chart below before
consulting a SERVICE CENTRE APPROVED BY SHARP. This will help to prevent unnecessary service calls.
• Repairs and Modifications: Do not attempt to operate the oven if it is not working properly.
• Outer cabinet & Lamp Access: Never remove the outer cabinet to avoid the possibility of electric shock or burns.
Error Message/Information Message
DISPLAY
ACTION
U 04
The oven is too hot to use AUTO (Reheat) and Defrost.
Remove food from oven and allow to cool until the message clears.
C
number
Due to technical error, contact a SERVICE CENTRE APPROVED BY SHARP.
Troubleshooting Chart
The following situations are normal and are not signs that the oven is malfunctioning.
QUESTION / SITUATION
ANSWER
Control panel /
power supply
The display is black / blank.
*
Open the door and close.
* Check the power plug is properly connected to a
suitable wall outlet.
* Check the wall socket and fuse are functioning properly.
Electrical power supply is
interrupted during cooking.
* The programmed cooking time and mode will be
cancelled.
* Continue to cook manually.
The remaining time has
changed.
It is normal for Donabe RICE cooking. It is the standing
time for steaming. At first, the display counts down the
cooking time When it reaches zero, the oven will “beep”.
Continuously, the display will show and count down
its steaming time. See page E-8.
NOTE: In the following situations, the display will be blank
in approx. 5 minutes.
1. “0” is appeared on the display.
2. While you set any cooking programme.
3. Pause in AUTO (Reheat) or in Microwave Time Cooking.
Steam
Water is found inside the oven
when the door is opened.
Steam has condensed inside the oven. Wipe dry with a
soft cloth or a sponge after cooling.
Noise / Sound
Noise during cooking.
* The cooling fan will operate during cooking.
* The oven will control the output power.
Noise after cooking.
The cooling fan will operate until the oven is cool.
The fan may continue to operate for 1 minute
30 seconds.
3 short beeps sound.
Smoke / Aroma
The oven cavity smells after
cooking.
Check the oven cavity is clean without any food spatters.
It is important to clean the oven interior after every use.
The menu does not have a good
result.
* Check the food is put in the centre of the oven floor.
* Check the food quantity is correct.
Others
No sound when pressing any pads.
The oven is in mute. See page E-11.
It is the reminder sound. It will sound 3 times every 1
minute after cooking unless door is opened or
STOP/CLEAR is pressed.
Any pads do not activate.
Retry after pressing STOP/CLEAR.
