Website:
http://www.sharp.co.uk/support
Help Line:
08705 274277 (office hours)
4
INSTALLATION
WARNING:
Inspect the Oven:
• Check the oven carefully for damage
before and regularly after installation.
• Make sure the door closes properly,
that it is not misaligned or warped.
• Check the hinges and door safety
latches are not broken or loose.
• Ensure the door seal and sealing
surfaces are not damaged.
• Inspect the oven interior and door for
dents.
IMPORTANT:
If any damage is apparent, do not operate
the oven in any way. Contact your dealer
or SHARP approved service facility. (see p.
62)
1. Remove all packing materials including the feature
sticker (if applicable). Do not remove the plastic film
from the inside of the oven windo as this protects it
from dirt. The waveguide cover prevents food and
grease from entering the waveguide area where it
could cause damage. DO NOT REMOVE.
2. Place oven on a secure, level surface, strong
enough to take the oven weight, plus the heaviest
item likely to be cooked in the oven.
3. The minimum height of
free space necessar y
above the top surface of
the oven is 19cm.
4. The oven door may
become hot during
cooking. Place or mount the oven so that the bottom
of the oven is 85cm or more above the floor.
5. Do not place the oven where heat, moisture or high
humidity are generated, (for example, near or
above a conventional oven) or near combustible
materials (for example, curtains). Do not block or
obstruct air vent openings. Do not place objects on
top of the oven.
6. Make sure the power supply cord is undamaged
(See IMPORTANT! ELECTRICAL CONNECTION
opposite) and that it does not run under the oven or
over any hot or sharp surfaces.
7. The socket must be readily accessible so that it can
be easily unplugged in an emergency.
8. Do not use the oven outdoors.
BUILDING-IN-KIT.
An installation frame is available which enables the
microwave oven to be integrated within a kitchen unit.
The microwave oven is not designed to be built above
or near a conventional oven.
SHARP recommend the use of the build in kit,
EBR-4600, available from your SHARP dealer. Only
the use of this frame will guarantee the quality and
safety of the oven. When building, follow installation
instructions supplied carefully.
IMPORTANT! ELECTRICAL CONNECTION.
• Do not allow water to come into contact with the
power supply cord or plug.
• Insert the plug properly into the socket.
• Do not connect other appliances to the same socket
using an adaptor plug.
• If the plug or socket is loose or the power supply
cord is damaged, it must be replaced with a special
cord. The exchange must be made by an authorised
SHARP service agent.
• When removing the plug from the socket always
grip the plug, never the power supply cord as this
may damage the power supply cord and the
connections inside the plug.
• If the fitted mains plug to your oven is a rewireable
type and in the unlikely event of the socket outlet in
your home not being compatible with the plug
supplied, remove the plug and fit an appropriate
type, observing the wiring code given in `To replace
the mains plug’ on page 61.
If you wish to remove or replace the plug supplied,
ensure the plug is removed properly and not cut off.
• If the plug fitted to your oven is a non-rewireable
plug and in the unlikely event of the socket outlet in
your home not being compatible with the plug
supplied, cut-off the mains plug and fit an
appropriate type, observing the wiring code given in
‘To replace the mains plug’ on page 61.
Danger:
The fuse from the cut-off plug should be removed and
the plug disposed of in a safe manner.
Under no circumstances should the cut-off plug be
inserted into a socket outlet as a serious electric shock
may occur.
The plug must not be used without the fuse cover fitted.
If you have any doubt about your microwave oven
obtain the help of a qualified electrician.
If you wish to remove or replace the plug supplied,
ensure the plug is removed properly and not cut off.
When replacing the plug please ensure that you use a
BSI or ASTA approved plug to BS1363, this should be
fitted with a brown coloured 13 amp fuse approved by
BSI or ASTA to BS1362. If you have any doubt about
electrical connection seek the help of a qualified
electrician.
WARNING: THIS APPLIANCE MUST BE
EARTHED
To wire an appropriate plug, follow the wiring code
given in `To replace the mains plug’ on page 61.
19cm
R-774M O/M 24/05/2001 09:26 Page 4
http://www.usersmanualguide.com/
