Sharp AR-5127, Service Manual

Page: 63 / 94

AR-5127 SIMULATION 8 - 35
Operation/procedure
Enter a figure with the 10-key.
[When key input = 1]
Self print is performed in the 2-by-4 mode
Since scanning is not performed, if a document is set on the SPF, the
START key is invalid.
* Duplex print is invalid.
[When key input = 2]
Grid print is performed. (1cm, 1-dot width WLT/A3 print (A3 main scan,
WLT sub scan))
If the IMC board is not installed, key input cannot be made.
* Duplex print is allowed.
[7-seg LED display]
1: Self print (2-by-4) mode
2: Grid print mode
Pressing the [START] key makes a print by 2 by 4 mode. After comple-
tion of printing, the menu returns to the initial menu.
Pressing the [CA] key cancels the simulation mode.
Note: Executable only when the IMC board is installed.
Operation/procedure
Check the key input of the operation panel.
Press the keys displayed on LCD sequentially.
After completion of all key entries, "COMPLETE" is displayed.
Operation/procedure
Display FAX software SW on LCD, and set/change those with 10-key.
Note: Executable only when the FAX is installed.
Operation/procedure
Used to clear the FAX-related soft switches except for the line signal
adjustment value and the machine adjustment value and to set default
values (which differ depending on the country code separately
entered.)
Note: Executable only when the FAX is installed.
Operation/procedure
Read/write can be checked for FAX PWB memory.
The check result is displayed separately for each memory.
1. Memory to be checked
2. Detailed procedure
Interruption cannot be made during operation.
Note: Executable only when the FAX is installed.
64
64-1
Purpose Operation test/check
Function
(Purpose) Self print
Key input = 1
Self print is performed in the 2-by-4 mode (2-line print
and 4-line non-print).
Key input = 2
Grid print is performed. (1cm, 1-dot width WLT/A3 print
(A3 main scan, WLT sub scan))
Section Printer
Item Operation
(Input screen) (Executing screen)
65
65-5
Function
(Purpose) Used to check the operation panel.
Section Operation (screen/operation)
(1) (2) (3)
Sim65-5 KEY CHECK
COPY
Sim65-5 KEY CHECK
FAX
Sim65-5 KEY CHECK
COMPLETE
66
66-1
Purpose Adjustment/Setting/Check
Function
(Purpose) FAX related soft SW setting
66-2
Purpose Adjustment/Setting/Check
Function
(Purpose) Initial set for the value of the FAX soft SW
66-3
Purpose Adjustment/Setting/Check
Function
(Purpose) FAX PWB memory check
DRAM
SRAM
Flash ROM
Program area SUM check only
Memory area
Option memory The memory size follows the
automatically detected value.
PAGE
1 "55H" is written to all the addresses of each memory, and the
address data are read in sequence to check that they were
properly written.
2 "AAH" is written to all the addresses of each memory, and the
address data are read in sequence to check that they were
properly written.
3 "00H" is written to all the addresses of each memory, and the
address data are read in sequence to check that they were
properly written.
4 Perform checks 1 - 3 sequentially. If there is no abnormality, it is
"OK." If there is any abnormality, "NG" is notified to the error
address.
5 After completion of check, the memory is returned to the initial
state.
(CPU is not reset)
66-4
Purpose Adjustment/Setting/Check
Function
(Purpose) Signal send mode
Related soft
SW SW5-5 to 8 (signals send level)
SW23-1 to 4 (RBT ON time)
SW23-5 to 8 (RBT OFF time)
SW43-1 to 5 (DTMF signal send time)