Sharp AR-5127, Service Manual

Page: 37 / 94

AR-5127 SIMULATION 8 - 9
When selected without setup, the selected value is registered and
highlighted. When selected with previous setup, the previous setup is
canceled and it is displayed normally.
This setting is canceled by power OFF.
Note: In SIM 7-1, pressing [CA] key terminates the simulation and the
machine enters the aging mode without resetting. Therefore, to
perform "4. Intermittent setup," the intermittent cycle must be set
with SIM 7-6 in advance.
Reset is not performed when the machine enters the aging
mode.
Operation/procedure
Enter the interval aging cycle time (sec) with the 10-key pad. Refer to
7-1.
Operation/procedure
Warm-up starts by the cover open/close.
(Can be performed repeatedly by open/close of the cover.)
The warm-up time is counted up and displayed in the unit of sec.
If the [CA] key is pressed at this time, count-up is interrupted to termi-
nate the simulation. (However, warm-up is continued.)
After completion of warming up, "WARM UP COMPLETED" is dis-
played and the control returns to the initial screen.
Operation/procedure
After selecting the mode, enter the adjustment value and press the
[OK] key, and output will be made for 30sec.
( ∗ ) Linked with the destinations of SIM 26-6.
Linked with the auto exposure mode of SIM 46-19-1.
* SUPER PHOTO (5:) cannot be executed.
When [OK] or [START] key is pressed, a caution buzzer sounds.
(Only the adjustment value can be entered.)
The minimum increment is 2V.
The result of (Set value – 199) / 2 is stored in the EEPROM.
When reading a value from the EEPROM, the value of (EEP value *2)
+ 200 is used as the set value.
Therefore, the set value entered must be an even number. If an odd
number is entered the entered odd 1 is displayed after
pressing [OK] key.
Operation/procedure
After selecting the mode, enter the adjustment value and press the
[OK] key, and output will be made for 30sec.
The input value is in the increment of –25V.
( ∗ ) Linked with the destinations of SIM 26-6.
Linked with the auto exposure mode of SIM 46-19-1.
* SUPER PHOTO (5:) cannot be executed.
When [OK] or [START] key is pressed, a caution buzzer sounds.
(Only the adjustment value can be entered.)
7-6
Purpose Setting/Operation test/check
Function
(Purpose) Used to set the cycle of intermittent aging.
Item Operation
Setting range 1-255
Default
3
7-8
Purpose Setting/Operation test/check
Function
(Purpose) Used to set the display of the warm-up time.
Item Operation
(Initial screen) (Executing screen) (Initial screen after completion)
8
8-1
Purpose Adjustment/Operation test/check
Function
(Purpose) Used to check and adjust the operation of the
developing bias voltage in each copy mode and the
control circuit.
Section Image process (Photoconductor/Developing/Transfer/
Cleaning)
Developer/Toner hopper
Sim7-6 INTERVAL SET
AGING INTERVAL 3
[ 1-255] 3
Sim7-8 WARM UP TIME
PLEASE COVER
OPEN AND CLOSE
Sim7-8 WARM UP TIME
WARMING UP,
PLEASE WAIT.
1
Sim7-8 WARM UP TIME
PLEASE COVER
OPEN AND CLOSE
WARM UP COMPLETED.
10
(Initial screen) (Input/Selection screen) (Executing screen)
Display items Content
Installation
range
Default
1:AE
AE ( ∗ ) 200-550 400 (–400V)
2:TEXT
Character 450 (–450V)
3:TEXT/PHOTO
Character/Photo 450 (–450V)
4:PHOTO
Photo 450 (–450V)
5:SUPER PHOTO *
Super photo Disabled
6:TONER SAVE
Toner save 376 (–376V)
8-2
Purpose Adjustment/Operation test/check
Function
(Purpose) Used to check and adjust the operation of the main
charger grid voltage (high mode) in each copy mode
and the control circuit.
Section Image process (Photoconductor/Developing/Transfer/
Cleaning)
Photo conductor
(Initial screen) (Input/Selection screen) (Executing screen)
Display items Content
Setting
range
Default
1:AE
AE ( ∗ ) 1-8 3 (–530V)
2:TEXT
Character 5 (–580V)
3:TEXT/PHOTO
Character/Photo 5 (–580V)
4:PHOTO
Photo 5 (–580V)
5:SUPER PHOTO *
Super photo Disabled
6:TONER SAVE
Toner save 2 (–505V)
Sim8-1 DV BIAS COPY
1:AE 400
2:TEXT 450
3:TEXT/PHOTO 450
1/2
Sim8-1 DV BIAS COPY
5:SUPER PHOTO 400
EXEC [200-550] 400
Sim8-1 DV BIAS COPY
5:SUPER PHOTO 400
EXEC [200-550] 400
Sim8-2 MHV(H) COPY
1:AE 3
2:TEXT 5
3:TEXT/PHOTO 5
1/2
Sim8-2 MHV(H) COPY
5:SUPER PHOTO 3
EXEC [ 1- 8] 3
Sim8-2 MHV(H) COPY
5:SUPER PHOTO 3
EXEC [ 1- 8] 3