manualshive.com logo in svg

Sharp AR-317 Operation, Key Operator'S Manual, Page: 98 / 302

Share
Download
Sharp AR-317 Operation Key Operator'S Manual Download Page 98

72

TROUBLESHOOTING AND MAINTENANCE

MISFEED IN THE UPPER EXIT AREA
(when a  job separator tray kit or finisher (AR-FN5A) is installed)

If a job separator tray kit or a finisher is installed, a misfeed may occur in the upper exit area.

1

Open the upper right side cover.

2

Gently pull the misfed paper out.

Be careful not to tear the 
misfed paper during 
removal.

3

Close the upper right side cover.

Make sure that the misfeed message is cleared.

MISFEED IN AN OUTPUT TRAY 
(when a finisher (AR-FN5A) is installed)

1

Grasp the handle of the stapler 
compiler cover and pull to open the 
cover.

2

Remove any misfed paper from the 
transport area.

A MISFEED HAS OCCURRED.

INFORMATION

!Andromeda_copy_sec.book  72 ページ  ２００６年１１月２３日　木曜日　午後６時１分

Summary of Contents for AR-317 Operation















































































































































































































































































































Reviews:

No comments