Sharp AR-317 Operation Key Operator'S Manual Download Page 35

Page: 35 / 302

BEFORE USING THE MACHINE

Interior

Paper trays

Each tray holds 500 sheets of copy paper. (p.15)

Upper right side cover

Open to remove misfeeds when an optional job
separator tray kit or a optional finisher is installed.
(p.72)

Side cover

Open to remove misfeeds. (p.68)

Side cover handle

Pull to open the side cover. (p.68)

Bypass tray paper guides

Adjust to the width of the paper. (p.18)

Bypass tray

Regular paper and special paper (such as
transparency film) can be fed from the bypass tray.
(p.18)

Bypass tray extension

Pull out the bypass tray extension before placing
paper in the bypass tray. (p.18)

Toner cartridge lock release lever

Use to unlock the toner cartridge. (p.74)

Toner cartridge

Contains toner. (p.74)

Roller rotating knob

Turn to remove misfed paper. (p.68)

Photoconductive drum

Copy images are formed on the photoconductive
drum.

Fusing unit release levers

To remove a paper misfeed in the fusing unit, push
up on these levers and remove the paper. (p.69)

Fusing unit paper guide

Open to remove misfed paper. (p.69)

Do not touch the photoconductive drum
(green portion). Doing so may damage the
drum and cause smudges on copies.

The fusing unit is hot. Do not touch
the fusing unit when removing
misfed paper. Doing so may cause a
burn or injury.

The model name is on the front cover of the
machine.

Caution

Warning

Note

!Andromeda_copy_sec.book 9 ページ２００６年１１月２３日　木曜日　午後６時１分

Summary of Contents for AR-317 Operation















































































































































































































































































































Search results

Summary of Contents for AR-317 Operation

Reviews:

Brands by name

Popular brands

Sharp AR-317 Operation, Key Operator'S Manual

Search results

Summary of Contents for AR-317 Operation

Reviews:

Brands by name

Popular brands