Sharp AR-317 Operation Key Operator'S Manual Download Page 34

Page: 34 / 302

Chapter 1

BEFORE USING THE MACHINE

This chapter contains basic information that should be read before using the machine.

PART NAMES AND FUNCTIONS

Exterior

Document feeder tray

Place the original(s) that you wish to scan face up
here. (p.23)

Original guides

Adjust to the size of the originals.

Document feeder cover

Open to remove misfed originals. (p.67)

Reversing tray

Pull out to remove misfed originals. (p.67)

Exit area

Originals exit the machine here after copying.

Document transport cover

Open to remove misfed originals. (p.67)

Document transport cover knob

Pull to open the document transport cover (p.67)

Document glass

Place an original that you wish to scan face down
here. (p.22)

Power switch

Press to turn the machine power on and off. (p.13)

Handles

Use to move the machine.

Operation panel

Contains operation keys and the touch panel.
(p.10)

Job separator tray (Upper tray) (optional)

Print jobs and received faxes are delivered to this
tray.

Center tray

Finished copies are delivered to the center tray.

Front cover

Open to remove paper misfeeds and perform
machine maintenance. (p.68)

!Andromeda_copy_sec.book 8 ページ２００６年１１月２３日　木曜日　午後６時１分

Summary of Contents for AR-317 Operation















































































































































































































































































































Search results

Summary of Contents for AR-317 Operation

Reviews:

Related manuals for AR-317 Operation

Brands by name

Popular brands

Sharp AR-317 Operation, Key Operator'S Manual

Search results

Summary of Contents for AR-317 Operation

Reviews:

Related manuals for AR-317 Operation

Brands by name

Popular brands