Sharp Aquos LC-32LE600E Manual Download Page 69

Page: 69 / 100

LC-32/40/46LE600E/RU/S

6 – 23

2.18. IC9605/IC9608 (VHi-1Y)

2.18.1 Block Diagram

2.18.2 Pin Connections and short description

Pin No.

Pin Name

I/O

Pin Function

BOOT

Upper part MOS transistor boot strap capacity connection terminal.
Connect the boot capacity of about 0.022

F between SW terminals.

The boot capacity series resistance (about100

Ω

) is effective for stable operation.

VIN

Input power source terminal.
Connect very big capacity (10

F 2 or more) between GND.

Power switch terminal.
Connect the output LC filter. Connect the above-mentioned capacity between BOOT terminals.

GND

—

Ground

Feedback terminal.
The output voltage is set by the division resistance of output voltage (Vout-FB-GND).

COMP

Phase compensation terminal.
Connect external capacity and resistance for the phase compensation of the DC/DC converter close loop.

Enable terminal
It operates the converter by a high voltage or the opening. It stops with GND the converter operation.

—

Soft start terminal.
The soft start time is set by built-in 10

A source voltage and external soft start capacity.

Summary of Contents for Aquos LC-32LE600E





































































































Search results

Summary of Contents for Aquos LC-32LE600E

Reviews:

Related manuals for Aquos LC-32LE600E

Brands by name

Popular brands

Sharp Aquos LC-32LE600E, Manual

Search results

Summary of Contents for Aquos LC-32LE600E

Reviews:

Related manuals for Aquos LC-32LE600E

Brands by name

Popular brands