Sharp Aquos LC-32LE600E Manual Download Page 17

Page: 17 / 100

LC-32/40/46LE600E/RU/S

4 – 12

16. Upgrading the software

1. Unplug AC cable from outlet.

2. Insert an USB memory that is written a new software to USB port.

3. Keep pressing POWER button on LCD panel and plug AC cable to outlet.

4. POWER LED on panel automatically start blinking.

(POWER LED: Both red and green light blinking with sync. In other word, it looks, /blinking period is short ... 2 cycle - light - out - light - out / 1 sec.)

5. After a while (about 2 min.) following screen appears. Indicated percentage means progress of version up.

6. After the progress becomes 100%, then STATUS area changes “UPGRADE COMPLETE” as followings (POWER LED: Only green blinks slowly ...

2 sec./time).

* If above screen is not appeared and “UPGRADE FAILURE” is indicated in STATUS area, at that time update failure. Please repeat from step 1.

(POWER LED: Only red blinks slowly ... 2 sec./time).

7. Unplug AC cable from outlet.

8. Remove USB memory from USB port.

System Version: EXXXXXXX

STATUS

UPDATING...

System Version: EXXXXXXX

100%

STATUS

UPGRADE COMPLETE

System Version: EXXXXXXX

50%

STATUS

UPGRADE FAILURE

Summary of Contents for Aquos LC-32LE600E





































































































Search results

Summary of Contents for Aquos LC-32LE600E

Reviews:

Related manuals for Aquos LC-32LE600E

Brands by name

Popular brands

Sharp Aquos LC-32LE600E, Manual

Search results

Summary of Contents for Aquos LC-32LE600E

Reviews:

Related manuals for Aquos LC-32LE600E

Brands by name

Popular brands