Sharp Aquos LC-32LE600E Manual Download Page 18

Page: 18 / 100

LC-32/40/46LE600E/RU/S

5 – 1

LC32LE600E

Service Manual

CHAPTER 5.

TROUBLESHOOTING TABLE

[1] TROUBLESHOOTING TABLE

<POWER BLOCK: LC-32LE600E/RU/S>

No power supply (Front LED does not light up) and no power-up even if turned on (Front LED light up).

Is the wire harness in the unit properly connected?

Reconnect and recheck the wire harness.

YES

Are F7001 and F7002 normal?

Are L7004, L7001,L7002,BD7001 etc. faulty?
Check if the peripheral circuits are short-circuited.

YES

Is BU+5V supplied from pin(11) of connector CN7003 (PD) when
the power switch is turned off?

Check the peripheral circuits,
IC7101, T101, C7401, C7403, PC7008, etc

⋅

YES

Is the PS_ON signal sent to pin(10) of connector CN7003 (PD)
when the power switch is turned on

Check pin(AC11) of IC3303(VCT_P) on MAIN PWB.

YES

Is the AC_DET signal sent to pin(9) of connector CN7003 (PD)
when the power switch is turned on?

Check the peripheral circuits,PC7007, Q7004, PC7002,etc.

YES

Is the DC voltage of approx. 400V supplied to both ends of
C7015?

Does the PFC circuit normally work?
(Check IC7002, L7003, TH7001, IC7001, Q7005, Q7006etc. and
the peripheral circuits.)

YES

Is UR13V supplied from pins(1-4) of connector CN7003 (PD)
when the power switch is turned on?

Check the peripheral circuits
(T7002, D7051, L7051, PC7001)

YES

Is PNL12V supplied from pins(1-2) of connector CN7004 (PL)
when the power switch is turned on?

Check the peripheral circuits (U7053, etc

⋅

)

YES

Is 144V supplied from pins(2,4,6) of CN7007(LA2) and
pins(2,4,6,8,10,12) of CN7006 (LA1) when the power switch is
turned on?

Check the peripheral circuits,
T7501, D7501, C7501, FA5511,etc

⋅

Summary of Contents for Aquos LC-32LE600E





































































































Search results

Summary of Contents for Aquos LC-32LE600E

Reviews:

Related manuals for Aquos LC-32LE600E

Brands by name

Popular brands

Sharp Aquos LC-32LE600E, Manual

Search results

Summary of Contents for Aquos LC-32LE600E

Reviews:

Related manuals for Aquos LC-32LE600E

Brands by name

Popular brands