Sharp Aquos LC-32LE600E Manual Download Page 34

Page: 34 / 100

LC-32/40/46LE600E/RU/S

5 – 17

<When EXT1 is used for external input> No picture on the display (2)-3

No Y/C output when the EXT1 external input is used.

Checklist:
1) Is “INPUT SOURCE” button

on the remote control set up correctly?

•••

set it as “EXT1” with the INPUT SOURCE button on the remote

control.

2) Is MENU-Picture-Backlight/Contrast/Brightness set to “MIN”?

•••

Set it to an appropriate level.

3) Check the connection to the external device

•••

Connect it correctly as per the operation manual for the device.

4) Attention: The terminal of IC3303 (VCT) cannot be actually checked by hiding oneself, and check it with another terminal of the same line,

please.

Is the Y/C signal sent to pins (20) and (15) of SCART1 (SC503)?
(Y/C1)

Check external connection, input setting, SCART1 (SC503) and
peripheral circuits.

YES

Is the Y/C signal (Y/C1) sent to input terminal pins (AE24) and
(AF24) of IC3303 (VCT)?

Check between pins (20) (15) of SCART1 (SC503) and pins
(AE24) (AF24) of IC3303 (VCT), and peripheral circuits.

YES

Is the LVDS video signal (LVDS0_D [0:4]

) input to pins (40)-

(28) of LW Connector (P2601), and is CLK signal (TCLK

) input

to pins (32)/(33)?

Check whether there is short circuit between [A6:A11], [B6:B11]
pin of IC3303 (VCT) and (40)-(28) pin of LW Connector (P2601),
and peripheral circuits.

YES

Is the I2C signal (VCOM_SDA/SCL) send to pin(12)/(13) of LP
Connector (P2602)?

Check the I2C signal of IC2602 and peripheral circuit.

YES

Is the PNL12V output to pin (1)/(2) of PL Connector (CN7004(32
inch)/CN7503(40/46 inch)) of POWER UNIT?

Check PL connector of POWER UNIT and U7053(32inch)/
IC7502(40/46inch).

YES

Exchange LCD-CONT-UNIT and do it operate normally?

Check the contact of the LCD-CONT-UNIT connection harness
(LW/LP/PL).
Exchange LCD-PANEL if it is useless even if it exchanges it.

Summary of Contents for Aquos LC-32LE600E





































































































Search results

Summary of Contents for Aquos LC-32LE600E

Reviews:

Related manuals for Aquos LC-32LE600E

Brands by name

Popular brands

Sharp Aquos LC-32LE600E, Manual

Search results

Summary of Contents for Aquos LC-32LE600E

Reviews:

Related manuals for Aquos LC-32LE600E

Brands by name

Popular brands