Sharp Aquos LC-32LE600E Manual Download Page 19

Page: 19 / 100

LC-32/40/46LE600E/RU/S

5 – 2

<POWER BLOCK: LC-40/46LE600E/RU/S>

No power supply (Front LED does not light up) and no power-up even if turned on (Front LED light up).

Is the wire harness in the unit properly connected?

Reconnect and recheck the wire harness.

YES

Are F7001 and F7002 normal?

<40LE600E/RU/S>
Are L7001, L7002, L7003, D7101, D7103, VA7002, VA7001,
VA7003 etc... faulty?
Check if the peripheral circuits are short-circuited.

YES

<46LE600E/RU/S>
Are L7001, L7002, L7003, L7004, D7101, VA7002, VA7001,
VA7003 etc... faulty?
Check if the peripheral circuits are short-circuited.

Is F7102 normal?

Are TH7102, C7130, etc... faulty?

YES

Is BU+5V supplied from pin(11) of connector CN7501 (PD) when
the power switch is turned off?

Check the peripheral circuits (IC7102, T7101, C7510, PC7102,
PC7101, etc

⋅

)

YES

Is the PS_ON signal sent to pin(10) of connector CN7501 (PD)
when the power switch is turned on?

Check pin(AC11) of IC3303(VCT_P) on MAIN PWB.

YES

Is the AC_DET signal sent to pin(9) of connector CN7501 (PD)
when the power switch is turned on?

Check the peripheral circuits such as PS_ON circuits of Q7503,
PC7103, Q7118, Q7114 and PC7104, Q7501,Q7502, etc.

YES

Is the DC voltage of approx. 400V supplied to both ends of
C7144?

<40LE600E/RU/S>
Does the PFC circuit normally work?
(Check IC7104, L7105, TH7101, RL7101, IC7200, Q7109,
Q7110 etc... and the peripheral circuits.)

YES

<46LE600E/RU/S>
Does the PFC circuit normally work?
(Check IC7104, L7105, TH7101, RL7101, IC7101, Q7108,
Q7109 etc... and the peripheral circuits.)

Is UR13V supplied from pins(1-4) of connector CN7501 (PD)
when the power switch is turned on?

Check the peripheral circuits (T7102, D7507, C7514,7515,7516,
PC7105, PC7106, IC7503 etc...)

YES

Is PNL12V supplied from pins(1-2) of connector CN7503 (PL)
when the power switch is turned on?

Check the peripheral circuits (IC7502, etc

⋅

)

YES

<40LE600E/RU/S>
Is VLED supplied to pins(1-5) of CN7606(LA1) and pins(1-5) of
CN7607(LA2) when the power switch is turned on?

<40LE600E/RU/S>
Check the peripheral circuits, T7102, D7516, D7517, C7528,
L7501etc

⋅

<46LE600E/RU/S>
Is VLED supplied to pins(1-5) of CN7606(LA1), pins(1-5) of
CN7607(LA2), pins(1-3) of CN7608(LA3) when the power switch
is turned on?

<46LE600E/RU/S>
Check the peripheral circuits, T7102, D7516, D7517, D7518,
C7528, C7538, L7501etc

⋅

Summary of Contents for Aquos LC-32LE600E





































































































Search results

Summary of Contents for Aquos LC-32LE600E

Reviews:

Related manuals for Aquos LC-32LE600E

Brands by name

Popular brands

Sharp Aquos LC-32LE600E, Manual

Search results

Summary of Contents for Aquos LC-32LE600E

Reviews:

Related manuals for Aquos LC-32LE600E

Brands by name

Popular brands