Sharp AL-1633 Operation Manual Download Page 59

Page: 59 / 84

TROUBLESHOOTING

B. Misfeed in the fusing area

Push gently on both ends of the front
cover and open it.

Turn the roller rotating knob in the
direction of the arrow.

Carefully remove the misfed paper.
Lower the fusing unit release levers to
allow easier removal.

Be careful not to tear the
misfed paper during
removal.

Lift the fusing unit release levers, to
return them to their operating
position.

Close the front cover and side cover.

The misfeed indicator
(

) will go out.

The fusing unit is hot. Do not touch
the fusing unit when removing misfed
paper. Doing so may cause a burn or
injury.

• Do not touch the drum cartridge (green

portion) when removing the misfed paper.
Doing so may damage the drum and cause
smudges on copies.

• Be careful about unfixed toner on the

misfed paper soiling your hands or clothes.

Roller rotating knob

Fusing unit
release lever

Warning

Caution

• When closing the front cover, gently hold

both ends.

• When closing the side cover, press on the

handle.

• If the misfeed indicator (

) does not stop

blinking, check for torn pieces of paper in
the machine.

Note

AL-1633_1644_EX.book 57

ページ

２００３年１０月２３日　木曜日　午後８時２１分

Summary of Contents for AL-1633





















































































Search results

Summary of Contents for AL-1633

Reviews:

Related manuals for AL-1633

Brands by name

Popular brands

Sharp AL-1633, Operation Manual

Search results

Summary of Contents for AL-1633

Reviews:

Related manuals for AL-1633

Brands by name

Popular brands