Sharp AL-1633 Operation Manual Download Page 65

Page: 65 / 84

TROUBLESHOOTING

Remove the new drum cartridge from
the protective bag and gently insert
the lead end of the drum cartridge
along the guides.

Remove the protective cover from the
drum cartridge and then push the
cartridge all the way into the machine.

Insert the TD cartridge along the
guides until it locks in place.

If there is any dirt or dust
on the TD cartridge,
remove it before
installing the cartridge.

Close the front cover and side cover.

The drum cartridge
replacement required
indicator (

) will go

out.

Do not touch the drum cartridge (green
portion). Doing so may damage the drum and
cause smudges on copies.

• Before closing the front cover, make sure

that the TD cartridge and drum cartridge is
correctly installed.

• When closing the front cover, gently hold

both ends.

Caution

Note

!Chapter5.fm 63

ページ

２００４年３月２６日　金曜日　午前１１時３３分

Summary of Contents for AL-1633





















































































Search results

Summary of Contents for AL-1633

Reviews:

Related manuals for AL-1633

Brands by name

Popular brands

Sharp AL-1633, Operation Manual

Search results

Summary of Contents for AL-1633

Reviews:

Related manuals for AL-1633

Brands by name

Popular brands