Sharp AL-1633 Operation Manual Download Page 62

Page: 62 / 84

TROUBLESHOOTING

MISFEED IN THE LOWER PAPER TRAY

(Two-tray model only)

Open the lower side cover.

Grasp the handle to open
the lower side cover.

Remove the misfed paper.

Be careful not to tear the
misfed paper during
removal.

If the misfed paper is not seen in step
2, lift and pull out the lower paper tray
and remove the misfed paper.

Be careful not to tear the
misfed paper during
removal.

Close the lower side cover.

The misfeed indicator
(

) will go out.

Close the lower paper tray.

Make sure that there is no misfed paper in the tray before pulling it out. (p.56)

Note

If the misfeed indicator (

) does not stop

blinking, check for torn pieces of paper in the
machine.

Note

AL-1633_1644_EX.book 60

ページ

２００３年１０月２３日　木曜日　午後８時２１分

Summary of Contents for AL-1633





















































































Search results

Summary of Contents for AL-1633

Reviews:

Related manuals for AL-1633

Brands by name

Popular brands

Sharp AL-1633, Operation Manual

Search results

Summary of Contents for AL-1633

Reviews:

Related manuals for AL-1633

Brands by name

Popular brands