Sharp 4470 - FO B/W Laser Facsimile Operation Manual Download Page 82

Page: 82 / 148

Timer Operations

Press

and/or

to adjust the resolution and contrast if

desired, and then press

Load the document and then press

•

The document will be scanned into memory.

RESOLUTION

CONTRAST

START/
ENTER

Confidential transmission

(Continued from

Initial procedure

Enter the mailbox number (2 digits). (Go directly to Step 9 if the
receiving machine does not have mailboxes.)

Press

Dial the receiving machine using one of the following methods:

•

Press a Rapid Key.

•

Press

and enter a Speed Dial number (if you enter less than 2

digits, press

to complete the entry).

•

Enter a full fax number with the numeric keys.

Press .

START/
ENTER

SPEED DIAL

START/
ENTER

Summary of Contents for 4470 - FO B/W Laser





















































































































































Search results

Summary of Contents for 4470 - FO B/W Laser

Reviews:

Related manuals for 4470 - FO B/W Laser

Brands by name

Popular brands

Sharp 4470 - FO B/W Laser, Facsimile Operation Manual

Search results

Summary of Contents for 4470 - FO B/W Laser

Reviews:

Related manuals for 4470 - FO B/W Laser

Brands by name

Popular brands