Sharp 4470 - FO B/W Laser Facsimile Operation Manual Download Page 39

Page: 39 / 148

Adjusting the Resolution and Contrast

2. Sending

Documents

Contrast

The fax machine has three contrast settings:

The default setting is AUTO.

To adjust the contrast, press

until the desired setting appears in the

display.

AUTO

Use AUTO for normal documents.

DARK

Use DARK for faint documents.

LIGHT

Use LIGHT for documents with a dark
background.

CONTRAST

HALF TONE

STANDARD

FINE

SUPER FINE

RESOLUTION

(LIGHT)
M:00% SEND READY

( DARK)
M:00% SEND READY

( AUTO)
M:00% SEND READY

To adjust the resolution setting, press

one or more times until the

indicator light next to the desired setting comes on.

RESOLUTION

Summary of Contents for 4470 - FO B/W Laser





















































































































































Search results

Summary of Contents for 4470 - FO B/W Laser

Reviews:

Related manuals for 4470 - FO B/W Laser

Brands by name

Popular brands

Sharp 4470 - FO B/W Laser, Facsimile Operation Manual

Search results

Summary of Contents for 4470 - FO B/W Laser

Reviews:

Related manuals for 4470 - FO B/W Laser

Brands by name

Popular brands