Sharp 4470 - FO B/W Laser Facsimile Operation Manual Download Page 99

Page: 99 / 148

Print Hold

5. Spe

ial

Functions

Activating the Print Hold function

Once you have programmed a Print Hold code, follow the steps below to
activate the Print Hold function.

♦

A Print Hold code must be programmed before the Print Hold function can
be activated.

Press .

Press

to select YES.

PRINT HOLD

Display:

PRINT HOLD

ENTER

#(1-4, , )

4: ACTIVATE PRT. HOLD
1=YES, 2=NO

Press .

Press the numeric keys to enter the Print Hold code.

Press .

•

The received fax will print out.

PRINT HOLD

START/
ENTER

Printing received faxes

When the Print Hold function is activated, RCVD PRINT HOLD FAX will
appear in the display when a fax has been received to memory. Follow the
steps below to print the fax (or faxes).

Display:

PRINT HOLD

ENTER

#(1-4, , )

1:HOLD DATA PRINT
ENTER PASSCODE #

Summary of Contents for 4470 - FO B/W Laser





















































































































































Search results

Summary of Contents for 4470 - FO B/W Laser

Reviews:

Related manuals for 4470 - FO B/W Laser

Brands by name

Popular brands

Sharp 4470 - FO B/W Laser, Facsimile Operation Manual

Search results

Summary of Contents for 4470 - FO B/W Laser

Reviews:

Related manuals for 4470 - FO B/W Laser

Brands by name

Popular brands