Sharp 4470 - FO B/W Laser Facsimile Operation Manual Download Page 20 | Manualshive

Page: 20 / 148

background image

Installing the Print Cartridges

18

3

If you are replacing the drum cartridge,

remove the old cartridge and dispose
of it according to local regulations.

4

Remove the new drum cartridge from
its packaging. Insert the drum
cartridge into the print compartment.

•

Caution!

Excessive exposure to light

will damage the drum cartridge. Install
the cartridge promptly after removing it
from its packaging.

•

Make sure the drum cartridge is
inserted in as far as it will go.

5

If you are installing a new toner
cartridge, remove the new toner
cartridge from its packaging. Remove
the tape from the cartridge and then
open the cartridge handle so that it
stands straight up.

6

Shake as indicated by the arrows to
distribute the toner evenly within the
cartridge.

•

If the toner is still lumpy after shaking,
the gears in the cartridge may make a
noticeable sound when the print
compartment cover is closed after
installing the cartridge. This is normal
and does not indicate a problem.

GREEN

BLUE

«
...
18
19
20
21
22
...
»

Summary of Contents for 4470 - FO B/W Laser





















































































































































Reviews:

No comments

Related manuals for 4470 - FO B/W Laser

Brand: Datamax Pages: 2

Brand: Oki Pages: 62

Brand: TallyGenicom Pages: 144

Brand: Xerox Pages: 2

Brand: Xerox Pages: 16

Brand: Canon Pages: 542

Brand: Konica Minolta Pages: 12

EuroLine Series

Brand: Output Technology Pages: 73

BradyPrinter A5500

Brand: Brady Pages: 72

Brand: Xerox Pages: 85

Brand: Riso Pages: 82

Brand: Oki Pages: 2

Brand: Nagel Pages: 22

ActionPrinter 3250 - ActionPrinter-3250 Impact Printer

Brand: Epson Pages: 22

ActionPrinter 4000

Brand: Epson Pages: 2

ActionPrinter 3260 s

Brand: Epson Pages: 116

ActionPrinter 5000 - ActionPrinter-5000 Impact Printer

Brand: Epson Pages: 8

ActionPrinter 3250

Brand: Epson Pages: 133

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands