SEW-Eurodrive Movidrive MDX60B, Compact Operating Instructions

Page: 33 / 64

6
Service
Fault messages and list of faults
Compact Operating Instructions – MOVIDRIVE
®
MDX60B/61B
33
Fault Subfault
Code Designation Response
(P)
Code Designation Possible cause Measure
98 CRC fault Immediate
stop 0 "CRC via internal flash"
fault Internal device fault flash
memory defective. Sending in a device for repair
99 IPOS ramp
calculation Immediate
stop 0 "Ramp calculation" fault Only in IPOS
PLUS®
mode:
Positioning ramp is sinusoidal
or square and an attempt is
made to change ramp times
and traveling velocities with en-
abled inverter.
Rewrite the IPOS
PLUS®
pro-
gram so that ramp times and
traveling velocities can only
be altered when the inverter is
inhibited.
100 Vibration –
warning Display fault
(P) 0 Vibrations diagnostics
warning Vibration sensor warning (→
"DUV10A" operating instruc-
tions) Determine cause of vibra-
tions. Continue operation until
F101 occurs.
101 Vibration fault Rapid stop
(P)
0 Vibration diagnostics fault Vibration sensor signals fault SEW‑EURODRIVE recom-
mends that you remedy the
cause of the vibrations imme-
diately
102 Oil aging
warning Display fault
(P) 0 Oil aging warning Warning signal from the oil
aging sensor Schedule oil change
103 Oil aging fault Display fault
(P)
0 Oil aging fault Fault message from the oil
aging sensor SEW-EURODRIVE recom-
mends that you change the
gear unit oil immediately.
104 Oil aging – o-
vertempera-
ture Display fault
(P) 0 Oil aging overtemperature Overtemperature signal from
the oil aging sensor
• Let oil cool down
• Check if the gear unit cools
properly
105 Oil aging
ready signal Display fault
(P) 0 Oil aging ready signal Oil aging sensor is not ready
for operation • Check voltage supply of oil
aging sensor
• Check and, if necessary,
replace the oil aging sensor
106 Brake wear Display fault
(P) 0 Brake wear fault Brake lining worn Replace brake lining (→ "Mo-
tors" operating instructions).
107 Line compon-
ents Immediate
stop 1 For regenerative power
supply only: No feedback
signal from main contactor Main contactor defective • Check main contactor
• Check control cables.
108 DCS fault Display fault 0 DCS fault
1 Configuration data not
loaded correctly to DCS..B
option. Connection interrupted while
loading the program to the
DCS..B option. • Reload the configuration
files.
• Then switch the DCS..B op-
tion off and on again.
2 Invalid configuration data
for software version of the
DCS..B option. DCS..B option configured using
a wrong software version. • Configure the DCS..B op-
tion with the permitted
MOVISAFE
®
software ver-
sion.
• Then switch the DCS..B op-
tion off and on again.
3 Unit was programmed with
incorrect software inter-
face. Program or configuration data
was loaded into the unit with an
incorrect MOVISAFE
®
software.
• Check the DCS..B version
and parameterize it again
using a valid MOVISAFE
®
software.
• Then switch the DCS..B op-
tion off and on again.
4 Incorrect reference voltage • Incorrect reference voltage
• Faulty supply voltage of the
DCS..B option
• Faulty component on the
DCS..B option
• Check supply voltage of
DCS..B option.
• Switch DCS..B option off
and on again.
5
6 Faulty system voltage • Faulty supply voltage of the
DCS..B option
• Faulty component on the
DCS..B option
• Check supply voltage of
DCS..B option.
• Switch DCS..B option off
and on again.
7
10 Incorrect supply voltage. • DC 24 V supply voltage of
the DCS..B option is faulty.
• Faulty component on the
DCS..B option
• Check supply voltage of
DCS..B option.
• Switch DCS..B option off
and on again.
24770531/EN – 11/2017