manualshive.com logo in svg

SEW-Eurodrive MOVIDRIVE DFP11A, Manual, Page: 11 / 52

Share
Download
SEW-Eurodrive MOVIDRIVE DFP11A Manual Download Page 11

MOVIDRIVE

®

  PROFIBUS DFP11A

11

Assembly / Installation 

Instructions

2

It is not possible to change the PROFIBUS station address via the DIP switches while the drive
inverter is running. If the station address is changed, the new station address will only be effective
after the drive inverter has been switched off (mains supply and 24 V supply ON/OFF) and then
switched on again. The station address set for the drive inverter is displayed with the fieldbus mon-
itor parameter P092 Fieldbus Address on the DBG Keypad or on the MX_SHELL.
   

01223AEN

Fig. 7: Displaying the current PROFIBUS station address on the DBG Keypad or MX_SHELL

2.7

Setting the Bus Parameters

The default value setting for the bus parameters depends on the protocol version used. For straight
PROFIBUS-DP mode the DIP switch must be set at DP. This will activate the default bus parame-
ters (in particular the min. TSDR) for time-optimized DP mode in accordance with DIN E 19245
Part 3 / EN 50170. For mixed mode (FMS/DP) or straight FMS mode the DIP switch must be set at
FMS.   

00083AEN

Fig. 8: Setting the default bus parameters to DIN 19245

This switch only serves to select the default bus parameters. Independent of the setting of this
switch, the drive inverter at any time supports simultaneous use of the PROFIBUS protocol options
FMS and DP (Combislave functionality).
Any change to this DIP switch setting will only become effective after the drive inverter has been
switched off (mains supply and 24 V supply ON/OFF) and switched on again.

2.8

Display Elements     

LED Green RUN LED Red BUS FAULT

Meaning

Flashing at approx. 
3 Hz

Off

Option pcb is being initialized (only immediately after drive inverter power-up or reset)

On

Flashing at approx. 0.5 Hz Configured station address is not within the permitted range (0...126) 

→

 Set correct 

station address and switch the unit on again.

On

On

DP mode:
a) When the drive inverter is being commissioned or run up:
The drive inverter has not been set to data exchange mode by the DP master yet .
b) The timeout period has elapsed, the drive inverter was not addressed by the DP 
master. 
FMS mode: There is no active FMS link between the FMS master and the drive inverter.
Mixed mode FMS/DP: A combination of the above

4

092

Fieldbus Address

FMS/DP

DP

1   2   3   4

1   2   3   4

Address

Default bus parameters for
- FMS mode or
- FMS + DP mixed mode

Condition as delivered
FMS/DP active

Default bus parameters for
straight DP-PROFIBUS mode

Summary of Contents for MOVIDRIVE DFP11A





















































Reviews:

No comments