SEW-Eurodrive CMP40 Operating Instructions Manual Download Page 17 | Manualshive

Page: 17 / 88

SEW-Eurodrive CMP40 Operating Instructions Manual Download Page 17

Operating Instructions – Explosion-Proof CMP Synchronous Servomotors

17

4

Required tools/resources

Mechanical Installation

4

Mechanical Installation

4.1

Required tools/resources

• Standard tools
• Mounting device
• Operation with conductor end sleeves: Crimping tool and conductor end sleeves
• Crimping tool for plug connectors in case customers want to assemble cables them-

selves

• Removal tool

4.2

Before you start

Do only install the servomotor if the following conditions are met:
• The specifications on the nameplate of the servomotor correspond to the supply sys-

tem (line-powered drive) or the output voltage of the servo inverter (inverter-powered
drive).

• The drive is undamaged (no damage caused by transportation or storage)
• The ambient temperature corresponds to the information on the nameplate and on

the order confirmation.

• The surrounding area is free from oils, acids, gases, vapors, (ionizing) radiation, etc.
• The installation altitude must be no higher than 1000 m above MSL, otherwise the

drive must be designed to meet the special environmental conditions. In case of de-
viations, see nameplate/order confirmation.

4.3

Preliminary

Thoroughly clean the shaft ends and make sure that they are free from anti-corrosion
agent, dirt or the like. Use a commercially available solvent. Make sure that the solvent
does not come into contact with the bearing or sealing rings as it may damage the ma-
terial.

CAUTION!

Observe the safety notes in section 2 during installation.

STOP!

The bearing and the sealing rings can be damaged if exposed to solvents.
Possible material damages!
• Protect the bearing and sealing rings from exposure to solvents.

«
...
15
16
17
18
19
...
»

Summary of Contents for CMP40

























































































Reviews:

No comments