manualshive.com logo in svg

Sera PROFIBUS, Technical Manual

Share
Download
Sera PROFIBUS Technical Manual Download Page 9

www.sera-web.com

9

ELECTRICAL CONNECTIONS

The field bus box modules are connected via the supplied connection cable.

The INTERFACE MODULE has a socket and a plug, whereby no Y-connector is necessary. 

The supply voltage (+5 V DC) for the terminating resistor is only applied on the socket. 

The terminating resistor is only available as plug connector.

Level connection (1) 

Pin

Wire colour

Function (factory setting)

Pin 1

WH

(white)

not assigned

Pin 2

BN

(brown)

not assigned

Pin 3

GN

(green)

not assigned

Pin 4

YE

(yellow)

not assigned

Pin 5

GY

(grey)

not assigned

Pin 6

PK

(pink)

Pre-alarm level

Pin 7

BU

(blue)

Dry run

Pin 8

RD

(red)

GND

The inputs can be switched using a floating contact signal. 

Pre-alarm and dry running are set to normally open floating contacts at the factory.

The sockets of the connections are A-coded and the assignations of the functions are symbolically labelled.

PROFIBUS output (2) 

Pin No.

Signal

Description

Pin 1

VP

+5 V supply for terminating resistor

Pin 2

A-line

Negative RxD/TxD 

Pin 3

GND bus

Data ground

Pin 4

B-line

Positive RXD/TxD

Pin 5

Shield

Not connected internally, connected internally with PROFIBUS cable with shield

Thread

Cable shield

Must be connected externally with PE via cable filter according to PROFIBUS 

standard

PROFIBUS input (3)

Pin No.

Signal

Description

Pin 1

NC

NC

Pin 2

A-line

Negative RxD/TxD 

Pin 3

GND bus

Data ground. 

Pin 4

B-line

Positive RXD/TxD

Pin 5

Shield

Not connected internally, connected internally with PROFIBUS cable with shield

Thread

Cable shield

Must be connected externally with PE via cable filter according to PROFIBUS 

standard

 

ATTENTION

The M12 socket is inversely coded and has 5 pins. Pin 1 is 5 V DC and Pin 3 is GND for the active terminating resistor. 

These must never be used for any other functions as this can result in destruction of the device.

Pin 2 and Pin 4 carry the data of the PROFIBUS communication. These must never be reversed otherwise the communicati-

on is disrupted. Pin 5 is the shield that is not internally connected to the module.

RD

BN

GN

YE

GY

PK

BU

WH

Summary of Contents for PROFIBUS

































Reviews:

No comments

Brands by name

Popular brands

Load more brands