manualshive.com logo in svg

Sera PROFIBUS, Technical Manual

Share
Download
Sera PROFIBUS Technical Manual Download Page 10

10

www.sera-web.com

ELECTRICAL CONNECTIONS

Master

Slave

Slave

Repeater

Slave

Slave

Slave

Slave

Slave

Slave

Slave

Slave

Slave

Terminating resistor

Anschluss Pumpe (4) 

Pin No.

Function

Pin 1

+24 V supply voltage

Pin 2

Communication IM1

Pin 3

Communication IM2

Pin 4

not assigned

Pin 5

Communication IM3

Pin 6

Pre-alarm level

Pin 7

Dry run 

-

Pin 8

GND

Installation example / bus diagram

All devices are connected in a bus structure (line).

Up to 32 nodes (master or slaves) can be networked within one segment.

The first and the last device must be provided with a terminating resistor. The bus segments are connected to the overall network 

with repeaters (amplifiers), but remain electrically isolated. Up to maximum 126 nodes (including repeaters) can be connected 

within the overall network.

The bus nodes are identified by the bus address. Each address must be unique and may only be assigned once.

NOTE

The minimum cable length between the individual nodes must be at least 1 m for transmission rates of more than 1.5 Mbit/s. 

It must be ensured for the cable installation that the PROFIBUS cable does not run parallel with other live cables.

Summary of Contents for PROFIBUS

































Reviews:

No comments

Brands by name

Popular brands

Load more brands