manualshive.com logo in svg

Sera PROFIBUS, Technical Manual

Share
Download
Sera PROFIBUS Technical Manual Download Page 16

16

www.sera-web.com

OPERATION

PARAMETER

Adresse

001...125

Modules / Output

PUMP_STATE

Statuses of the pump. All operating modes of the pump are displayed here. Even if the pump is not in the Interface mode.

FLOW_STATE

Current delivery rate of the pump in litres / hour or strokes. Valid across operating modes.

COUNTER_STATE

Totaliser of the pump. 

BATCH_STATE, IMPULS_STATE, ANALOG_STATE

Pump information of the respective set operating mode. No module exists for the Manual operating mode as there is no infor-

mation except the current delivery rate.

INPUT1_STATE, INPUT2_STATE, INPUT3_STATE, OUTPUT1_STATE, OUTPUT2_STATE

Information of the inputs / outputs analogous to the associated CONTROL modules.

A_OUTPUT_STATE

Current analogue output current.

CALIBRATION_STATE

Information during a calibration.

PUMP_INFO_STATE

General pump information, Dependent on the pump type.

ALARM_STATE

Display of the error signals of the pump. Active bit means error is present.

Settings (parameters)

The module is sent using the PROFIBUS address 126. Only the „SSA“ function is activated 

with this address and a new address can be allocated via the network.

The address range 1-125 can also be set here if the addressing via SSA is not desired.

Summary of Contents for PROFIBUS

































Reviews:

No comments

Brands by name

Popular brands

Load more brands