SenTech STC-MBS322U3V Product Specifications Download Page 55

Page: 55 / 65

No.15S103-01

55/65

STC-MBS510U3V / STC-MCS510U3V / STC-MBS322U3V / STC-MCS322U3V

Specifications and Use

’s guide

7.12 Pixel Defect Correction

Corrects the defect pixel, refer from horizontally beside pixel.
In the color camera, correct the defect pixel refer from horizontally beside same color pixel.

When consecutive defect pixels are selected, corrects up to 2pixels.

GenICamParameters

PixelCorrectionAllEnabled IBoolean Type

Switch ON/OFF on Pixel Defect Correction
True: ON, False: OFF

PixelCorrectionIndex

Integer Type

PixelCorrectionIndex

PixelCorrectionX

Integer Type

Defect position on X coordinate against Index was selected on
PixelCorrectionIndex

PixelCorrectionY

Integer Type

Defect position on Y coordinate against Index was selected on
PixelCorrectionIndex

PixellCorrectionEnabled

IBoolean Type

Switch ON/OFF on pixel defect correction against Index was
selected on PixelCorrectionIndex
True: ON, False: OFF

7.13 Trigger

As for the decryption of Trigger Type and Characteristic, please refer to the chapter Image acquisition and Camera
Mode.

When the external hardware or software signal is input, the following process should be done.

Line0

Line1

Line2

Line

Debouncer

Software Trigger

Trigger Source

Trigger

Delay

トリガー

Trigger

Selector

Trigger

Summary of Contents for STC-MBS322U3V


































































Search results

Summary of Contents for STC-MBS322U3V

Reviews:

Related manuals for STC-MBS322U3V

Brands by name

Popular brands

SenTech STC-MBS322U3V, Product Specifications

Search results

Summary of Contents for STC-MBS322U3V

Reviews:

Related manuals for STC-MBS322U3V

Brands by name

Popular brands