manualshive.com logo in svg

Sentec LuMon, Service Manual, Page: 12 / 33

Share
Download
Sentec LuMon Service Manual Download Page 12

Maintenance/Safety and Functionality Tests 

 

 

12 of 33 

Service Manual for the LuMon™ System 

 

3.1.5

 

Status indicator LEDs – LuMon™ Connector 

Connect the LuMon™ Connector  to the LuMon™ Monitor and switch on the monitor. During the power-up 

verify that the Status LED in the ControlBox lights up green 

 LED off. 

 

N

OTE

 

Any deviation from this sequence –  e.g. ControlBox LED lighting up blue or flashing red –  indicates that the 

LuMon™ Connector is defective and must be replaced (

8.1

). 

3.1.6

 

Function Test – SensorBeltConnector 

1. 

Connect the SensorBeltConnector to the LuMon™ Monitor and verify that the hardware and software 

version of the belt connector  (

A

/ 

Figure 3-1

)  is  displayed correctly in the ‘system settings’  area of 

ScoutView 

[1]

: 02.01.07-r288 4 1.02-r63 6. 

The numbers may vary but all numbers shall be present.

 

2. 

Connect  the  SensorBeltConnector  to the EIT Advanced Interface  (

2.4

). The indicator LED in  the 

MatchBox shall light up green indicating that the belt detection works properly. Verify that the ‘serial / 

lot no.’  (

B

/ 

Figure 3-1

)  on  ‘patient & belt’  area on ScoutView 

[1]

 

is displayed: e.g. ‘ETAV50200311-

000129’, numbers may vary. 

3. 

Rotate the EIT Advanced Interface left or right and verify on ScoutView that the displayed rotation 

changes accordingly. 

Figure 3-1: Function Test - Belt connector 

 

 

3.1.7

 

Function Test – LuMon™ Connector 

1. 

Connect the LuMon™ Connector to the LuMon™ Monitor and verify that the hardware and software 

version of the belt connector (

A

/ 

Figure 3-1

) is  displayed correctly in the ‘system settings’  area of 

ScoutView 

[1]

: 02.03.03-r335  4  3.15-r83  13. 

The numbers may vary but all numbers shall be 

present. 

2. 

Connect  the LuMon™ Connector  to the EIT Advanced Interface  using the LuMon™ Advanced 

Interface Adapter, the ribbon cable and the AC-Adapter (

2.4

).  Verify that the ‘serial / lot no.’  (

B

/ 

Figure 3-1

) on ‘patient & belt’  area on ScoutView 

[1]

  is displayed:  e.g. ‘ETAV50200311-000129’, 

numbers may vary). 

3. 

Rotate the MatchBox part of the belt connector – LuMon™ Advanced Interface Adapter – left or right 

and verify on ScoutView that the displayed rotation changes accordingly. 

Summary of Contents for LuMon


































Reviews:

No comments