SelectBlinds Skylight Installation & Care Instructions Download Page 23 | Manualshive

Page: 23 / 31

background image

11

ADJUST MOTOR LIMITS (IF DESIRED)

The lower and upper limits have been set at the factory. If you need to make

adjustments to the limits, follow the instructions below.

Please Note: When clearing the factory set limits, both the upper and lower

limits will need to be reset.

Use the

CHANNEL

buttons to select the channel for the shade that needs to be

adjusted. Then follow the directions below.

When adjusting one shade any other shades on that channel need to be

temporarily disabled. Set the switch on the motor to the “OFF” position.

Follow the limit setting instructions on next page and then turn the other shades

back on by setting the ON/OFF switch on the motor to the “ON” position.

«
...
21
22
23
24
25
...
»

Summary of Contents for Skylight
































Reviews:

No comments

Related manuals for Skylight

Brand: Style selections Pages: 4

Brand: Style selections Pages: 5

Brand: SelectBlinds Pages: 8

Brand: Marinello TENDE Pages: 2

Brand: Lafayette Pages: 4

Brand: YewdaleDefiant Pages: 8

Fabric Horizontal Blinds

Brand: Bali Pages: 8

Brand: RAAMDECORATIE Pages: 16

Brand: woundwo Pages: 8

Brand: Vimco Pages: 16

Brand: my home Pages: 20

PowerView EOS Duette

Brand: Hunter Douglas Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands