SelectBlinds Skylight Installation & Care Instructions Download Page 6

Page: 6 / 31

STEP 4: SHADE INSTALLATION

Apply supplied

silicone grease to

the ribs of guide

plugs where shown.

The guide plugs are

in the ends of the

middle rail.

Apply supplied silicone grease

to ribs of guide plugs

Track Retainer

“groove”

Guide Plug

Front of

Retainer

(room side)

It may be necessary to apply a small

amount of grease inside the track

retainer groove for smooth operation.

Save any left over grease in case future

applications are needed.

Tilt compressed top and middle rails

to position in retainer track. Make

sure the cords are hanging freely from

the middle rail and are not wrapped

around the guide plugs.

Insert one side of middle rail at a time

by positioning “barbed rib” on back

side of guide plug into groove of track

retainer.

Front View

Top

Rail

Middle

Rail

Bottom

Rail

Small Rail

Large Rail

Track Retainer

“groove”

Guide Plug

SMALL RAIL

LARGE RAIL

Front of

Retainer

(room side)

Summary of Contents for Skylight
































Search results

Summary of Contents for Skylight

Reviews:

Related manuals for Skylight

Brands by name

Popular brands

SelectBlinds Skylight, Installation & Care Instructions

Search results

Summary of Contents for Skylight

Reviews:

Related manuals for Skylight

Brands by name

Popular brands