SelectBlinds Skylight Installation & Care Instructions Download Page 21 | Manualshive

Page: 21 / 31

background image

9

STEP 8: INSTALL TRACKS

Place the track against the front of the

top and bottom rails. Make sure that

the notched track is placed on the right

with the notch at the top.

Attach the track with the screws

provided. Space the screws no more

than 12” apart.

Follow the same procedure for the

other track. Make sure that the 2 tracks

are parallel to each other.

4"

12”

12”

Attachment Screw

12”

12”

Front of track

overlaps front

of rails

Notch top/right

«
...
19
20
21
22
23
...
»

Summary of Contents for Skylight
































Reviews:

No comments

Related manuals for Skylight

Brand: YewdaleDefiant Pages: 8

Brand: Erfal Pages: 2

Brand: Erfal Pages: 4

Vision 32 Open Cassette

Brand: Louvolite Pages: 8

Premium Express Cordless 2" Faux Wood

Brand: AwardBlinds Pages: 2

Brand: IKEA Pages: 4

Brand: IKEA Pages: 4

Brand: IKEA Pages: 8

Automate MT01-1325-069001

Brand: rollease acmeda Pages: 16

Brand: Inspire Pages: 28

Brand: LuxaFlex Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands