Selco 56.01.00701, Instruction Manual

Page: 47 / 314

47
8 TECHNICAL SPECIFICATIONS
Saber 70 chp
Power supply voltage U1 (50/60Hz) 3x400Vac ±15% (50/60Hz) 3x230Vac ±15% (50/60Hz)
Zmax (@PCC)
*
86m Ω 43m Ω
Slow blow line fuse 16A 20A
Communication bus DIGITAL DIGITAL
Maximum input power (kVA) (EN/IEC) 10.4kVA 8.0kVA
Maximum input power (kVA) (SELCO) 11.6kVA 9.0kVA
Maximum input power (kW) (EN/IEC) 9.9kW 7.7kW
Maximum input power (kW) (SELCO) 11.0kW 8.7kW
Power factor PF 0.95 0.96
Efficiency ( μ ) 89% 89%
Cos
ϕ 0.99 0.99
Max. input current I1max (EN/IEC) 15A 20A
Max. input current I1max (SELCO) 16.7A 22.4A
Effective current I1eff (EN/IEC) 10.6A 15.5A
Effective current I1eff (SELCO) 11.8A 17.3A
Duty factor (40°C)
(x=50%) 70A -
(x=60%) 65A 55A
(x=100%) 55A 45A
Duty factor (25°C)
(x=100%) 60A 55A
Adjustment range I2 20-70A 20-55A
Step 1A 1A
Open circuit voltage Uo 252Vdc 252Vdc
IP Protection rating IP23S IP23S
Insulation class H H
Dimensions (lxdxh) 570x190x400 mm 570x190x400 mm
Weight 18.6 kg. 18.6 kg.
Manufacturing Standards EN 60974-1/EN 60974-10 EN 60974-1/EN 60974-10
Ambient temperature -10/+40°C -10/+40°C
Approval symbol EN 60974 EN 60974
Air flow YES YES
Power supply cable 4x2.5 mm2 4x2.5 mm2
Length of power supply cable 5 m 5 m
*
This equipment complies with EN/IEC 61000-3-11, EN/IEC 61000-3-12 if the maximum permissible mains impedance at the interface point
to the public grid (point of common coupling, PCC) is smaller than or equal to the Zmax stated value. If it is connected to a public low volt-
age system, it is the responsibility of the installer or user of the equipment to ensure, by consultation with the distribution network operator
if necessary, that the equipment may be connected.
Gas Air/Nitrogen Air/Nitrogen
Advised air pressure 5 bar 5 bar
Air minimum pressure 3 bar 3 bar
Minimum flow 185 l/min 185 l/min
Arc striking LIFT LIFT
Cutting capacity (Carbon steels)
Reccomended Cut (R) 20 mm 15 mm
Max Cut (M) 28 mm 22 mm
Separation (S) 35 mm 26 mm
Perforation (P) 15 mm 12 mm
Cutting capacity (Stainless steels)
Reccomended Cut (R) 18 mm 14 mm
Max Cut (M) 24 mm 19 mm
Separation (S) 30 mm 24 mm
Perforation (P) 12 mm 9 mm
Cutting capacity (Aluminum)
Reccomended Cut (R) 18 mm 13 mm
Max Cut (M) 22 mm 17 mm
Separation (S) 25 mm 22 mm
Perforation (P) 12 mm 9 mm
R: > 400 mm/min
,
M: > 250 mm/min, S: > 100 mm/min