Segway NINEBOT ONE S1 Service Manual Download

Page: 4 / 74

One S1

Contents

Trademark, Patent, and Contact Information .............................................................................3

Safety ............................................................................................................................7

Introduction ..................................................................................................................9

Hardware

Batteries ..................................................................................................................... 13

Battery Cover ...............................................................................................................................14

Battery ..........................................................................................................................................15

Battery Test ...................................................................................................................................16

Pedals ......................................................................................................................... 17

Pedals ...........................................................................................................................................18

Pedal Components .....................................................................................................................19

LED Strips .................................................................................................................. 21

LED Covers ..................................................................................................................................22

LED Strips .....................................................................................................................................23

Body ........................................................................................................................... 27

Body Disassembly .......................................................................................................................28

Body Assembly ............................................................................................................................32

Frame ......................................................................................................................... 37

Control Board Assembly ............................................................................................................38

Control Board Components ......................................................................................................40

Front/Rear Frames .......................................................................................................................42

Handle ..........................................................................................................................................43

ON/OFF Button ...........................................................................................................................44

ON/OFF Board ............................................................................................................................45

Charge Port ..................................................................................................................................46

Charge Port Cover ......................................................................................................................47

Buzzer ...........................................................................................................................................48

Temperature Sensor ...................................................................................................................49

Summary of Contents for NINEBOT ONE S1











































































Search results

Summary of Contents for NINEBOT ONE S1

Reviews:

Related manuals for NINEBOT ONE S1

Brands by name

Popular brands

Segway NINEBOT ONE S1, Service Manual

Search results

Summary of Contents for NINEBOT ONE S1

Reviews:

Related manuals for NINEBOT ONE S1

Brands by name

Popular brands