manualshive.com logo in svg

Segway NINEBOT ONE S1, Service Manual

Share
Download
Segway NINEBOT ONE S1 Service Manual Download Page 52

Wheel and Tire

52

One S1

Hub Brackets

Tools Required

•  13/16-inch socket

•  Pass-through socket wrench

• 

Large flathead screwdriver

Removal

  Make sure the One S1 is powered off and the 

charger is not connected.

1. 

Disassemble the One S1 (

page 28

).

2. 

Lay the wheel horizontally between two tables, as 
shown in 

Figure 74

.

3. 

Remove the hub nut, as shown in 

Figure 74

. Use 

a 13/16-inch pass-through socket wrench and a 

large flathead screwdriver (or metal rod) to turn 

the hub nut loose.

4. 

Use a flathead screwdriver to pop loose the axle 

clamps (

Figure 75

).

5. 

Lift the bracket and clamps off the wheel shaft

6. 

Remove the hub bushing (

Figure 76

).

Installation

1. 

Install in the reverse order of removal.

Figure 74:  Removing the hub nut

Figure 75:  Pop loose the axle clamps

Figure 76:  Remove the hub bushing

Hub Bushing

Summary of Contents for NINEBOT ONE S1











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands