background image

Release Version 1.2 

 

Please read this user’s manual thoroughly prior to the use this unit for its easy and convenient 
use. 

Caution  (If  you  do  not  keep  any  of  the  below  guidelines,  you  may  get  seriously 
injured or cause somebody’s death) 

■  Please make sure to install this product after unplugging power plug. Also, do NOT use this 

product by connecting many power plugs simultaneously. 

- It may cause abnormal heat, fire or electric shock. 

■  Do NOT leave this product at any place that water falls or splashes. Also, do NOT put 

anything, which is full of water such as a flower vase, on this product. 

- It may cause the malfunction or fire of the product if liquid goes into it. 

■  Do NOT open the product case randomly, disassemble, repair or remodel this product on 

your own because there is some high voltage parts. 

- It may cause fire, electric shock or injury due to abnormal operation. 

■  Do Not install this product at a place where there is high humidity, dust or soot. 

- It may cause electric shock or fire.   

■  Please keep the installation place clean and wipe the place with a dry towel. Also, do NOT 

use water, thinner or organic solvent. 

- It may cause damage on the product surface and may cause product problem or electric shock. 

■  Please leave this product at a cool place which does not have direct rays of the sun, keep the 

temperature optimal in the installation place, and leave the installation equipment or tools 
far away from where is crowded. 

- It may cause fire. 

■  Be careful of the danger that may be caused at humid floor, ungrounded power extension 

cable, worn-out power cord, lack of safety ground connection. If any problem is found, 
please contact where you purchased this product. 

- It may cause fire or electric shock. 

■  Please keep at least 15 Cm for the back of this device from the wall and keep at least 5Cm 

for the sides of this device from the wall. Otherwise, the cables may be bent and/or cut due 
to the narrow space between the device and the wall, and may cause malfunction or fire. 

- It may cause fire, electric shock or injury. 

■  In case of the input voltage for the operation of this device, the voltage fluctuation must be 

within 10% of the rated voltage and the power outlet must be grounded. In addition, the 
power outlet for this device shall not be used for other electric heating appliances such as 
hairdryers, irons, refrigerators, etc. 

- It may cause abnormal overheat, fire or electric shock. 

■  When thundering or lightning, please unplug the power plug for your safety. 

 

Caution  (If  you  do  not  keep  any  of  the  below  guidelines,  you  may  get  seriously 
injured or loss of property.) 

■  Do NOT install this product at where is exposed to strong magnetic or radio waves (RF) and 

adjacent to wireless devices such as radio or TV, etc.

   

■  Do NOT install this product at where has too high or low temperature or humidity. 

Precaution and Safety Guidelines

 

Summary of Contents for SC-16MHD





























Reviews: