SeeEyes SC-16MHD User Manual Download Page 10 | Manualshive

Page: 10 / 28

background image

Release Version 1.2

9

4-2. DEVICE

4-2-1. DISPLAY

▶ Enter [Device]

→

[Display] to show the following screen.

4-2-1-1. General

  - Set video output resolutions.
  - Set the CVBS video to NTSC, PAL or AUTO.
  - The default setting is ‘AUTO’.
  - Reboot this splitter after changing the settings to recognize the video signal again.
  - Transparency setting values are adjustable by +, - buttons on OSD menu.

Video Output
  - Select video output (Main Screen, Spot)
  - Click ‘Apply’ on the right side to complete the setup.
  - Reboot this splitter after changing the settings to recognize the video signal again.

* Some LEDs on the front interface may not be turned on when rebooting, and after completing its

reboot, the LED will be working properly.

«
...
8
9
10
11
12
...
»

Summary of Contents for SC-16MHD





























Reviews:

No comments

Related manuals for SC-16MHD

COMFOSPLIT IKARO

Brand: Ideal Clima Pages: 68

Brand: Mitsubishi Pages: 106

Infinity IEC-2001

Brand: LevelOne Pages: 2

DCS SCARLATTI DAC

Brand: Data Conversion Systems Pages: 26

Brand: N-Tron Pages: 2

enginko MCF-LW06485

Brand: M2M Pages: 14

Standard Extreme RAKK dac Mark III

Brand: Raleigh Audio Pages: 65

Brand: Icy Box Pages: 16

Nelson LINK DAC III

Brand: MSB Technology Pages: 12

Brand: Hama Pages: 8

PowerSourcePro REINVMA10

Brand: ring Pages: 122

Brand: Parasound Pages: 7

Smart AC Inverter 100 USB

Brand: Wagan Pages: 5

Brand: T-audio Pages: 27

Brand: Enerdrive Pages: 48

Brand: Visual Circuits Pages: 75

Brand: Diodes Pages: 5

Brand: tams elektronik Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands