background image

 

Section 4.  After Sales Support 

 

 

 

23 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

SEAL

 Brands Technical Service 

SEAL

 Brands Technical Service – Europe and  

(For technical assistance & service) 

Asia Pacific

 

 

(For technical assistance & service) 

Tel: 1-800-486-6502 

For UK: Tel: +44 1268 722 400 

Fax: 1-800-966-4554 

Fax: +44 1268 729 442 or +44 870 125 5798 

 

For NL: Tel: +31 572 345 500 

 

Fax: +31 572 345 501 

 

 

SEAL

 Brands Customer Service 

SEAL

 Brands Customer Service - Europe 

(For information and placing orders) 

(For information and placing orders) 

Tel: 1-800-257-7325 

Tel: +31 572 345 500 

Fax: 1-800-966-4554 

Fax: +31 572 345 501 

 
 

Note:

   SEAL Graphics recommends that your main power be installed by a licensed electrician in accordance with electrical codes in your area.  

Specifications subject to change without notice.  

 

Seal Graphics  

Seal Graphics  

Seal Graphics  

Seal Graphics  

Seal Graphics 

Americas Corporation

 

Canada

 

U.K. Ltd

 

Europe BV

 

Pacific Limited

 

7091 Troy Hill Drive 

1601 Matheson Blvd. E 

Unit 1, 1 Watkins Close 

Kanaaldijk O.Z.3 

Unit A, 13

th

 Floor, Block 1 

Elkridge, MD 21075 

Unit #4 

Burnt Mills Industrial Estate 

P.O. Box 29, 

Leader Industrial Centre 

Tel: 410-379-5400 

Mississauga, Ontario 

Basildon, Essex SS13 1BJ 

8100 AA Raalte 

Tsuen Wan, 

Fax: 410-579-8960 

Canada, L4W 1H9 

United Kingdom 

The Netherlands 

New Territories, Hong Kong 

 

Tel: 905-212-9232 

Tel: +44 1268 722 400 

Tel: +31 572 345 500 

Tel: +852 2407 3738 

 

Fax: 905-212-9313 

Fax: +44 1268 729 442 

Fax: +31 572 345 501 

Fax: -852 2408 0973 

 

 

www.sealbrands.com

 

 

© 2002 SEAL Graphics 
SEAL

 and Image

 are registered trademarks of SEAL Graphics 

Part #OM5000-E Rev. 3 

(11/02) 

 

Summary of Contents for AquaSEAL SW-5000

























Reviews: