950-0207revA - 9 - November 27, 2013
DRY mode
– Set point temperature can be set from 61°F to 86°F. Unit cools at 90% capacity
while the FAN runs in LOW speed only (FAN speed cannot be changed).
FAN mode
– Selects fan only operation. Set point temperature can be set from 61 °F to 86 °F.
Fan speed can be set to AUTO, HIGH, MEDIUM or LOW.
SLEEP
(Sleep 1 mode)
– In the COOL mode adjust the set-point temperature to a comfortable
setting, and then press the SLEEP button. After 1 hour, the set-point will increase by 1.8 ºF (1 ºC).
After 2 hours have passed temperature is increased by 3.6 ºF (2 ºC). Temperature will never increase
more than 3.6 ºF (2 ºC) from set-point or beyond 86 ºF (30 ºC). The temperature will stay at this setting
until the unit is turned off or the SLEEP function is disabled.
In the HEAT mode adjust the set-point temperature to a comfortable setting, and then press the
SLEEP button. After 1 hour the set-point will decrease by 1.8 ºF (1 ºC). After 2 hours have passed
temperature is decreased by 3.6 ºF (2 ºC). Temperature will never decrease more than 3.6 ºF (2 ºC)
from set point or below 61 ºF (16 ºC). The temperature will stay at this setting until the unit is turned off
or the SLEEP function is disabled.
The SLEEP mode does not work in the FAN or AUTO modes and is deactivated when the unit is
turned off or power is lost. On power up, the SLEEP mode must be turned on again if needed. Press
the SLEEP mode button to toggle SLEEP mode off and return to normal operation.
FAN
– Press this button to change fan speeds, AUTO, HIGH, MEDIUM or LOW, while in the
HEAT, COOL, FAN modes. When in the AUTO setting, the fan will run faster the further away from the
set point it gets. On the other hand the closer it gets to the set point the slower it will run.
CLOCK
– Press the CLOCK button, the clock ICON will start to blink. It will only blink for 5
seconds. While blinking press and hold down the + or - keys to adjust the 24H time of day clock to the
correct time. You must immediately press the CLOCK button to set the time. If the CLOCK button is
not pressed within 5 seconds, the clock time will revert back to the original setting and clock will have
to be set again.
TEMP
– Display indicates set point temperature.
PURGE
– When in the COOL or DRY mode and the PURGE function is enabled, the fan will
continue to operate for 10 minutes after the unit is turned off. This function dries the evaporation coil to
prevent mold and mildew. The PURGE function will remain enabled in DRY and COOL unless power is
interrupted or is disabled by the button. PURGE will not work in AUTO, FAN or HEAT modes.
TURBO
– The TURBO function will only run while in the HEAT or COOL mode. TURBO increases
indoor fan speed (more than high fan speed).
+ / - Raises or Lowers the set point temperature. Holding the button down for more than 2 seconds will
cause the set point to auto increment or decrement. This does not function in the AUTO mode since
the temperature set point cannot be changed.
DISPLAY
– Turns the display on or off on the indoor unit. None of the lights will be illuminated
when off is selected.
LOUVER UP AND DOWN
– Pressing the LOUVER positioning button slowly, (more than 2
seconds) will start and stop the louver swing. If the button is pressed to turn on swing and then
pressed again to turn it off, the louvers will remain in that fixed
position until it is turned on again.
Pressing the button quickly, (less than 2 seconds) will step through 5
different stationary positions and then on to 3 different swing
positions, similar to the ICONS.
Right to left louvers can be manually adjusted. CAUTION: Before adjusting the horizontal louvers turn
the unit off. Make the adjustments. Turn the unit back on. This will prevent possible personal injury and
or damage to the unit.
