background image

16

I&O manual

14

15

16

17

18

Detail information

No.

19/20

21

22

23

24

25

CN58/CN59

Filter board power supply port

CN44

Remote control port

            If the port is closed, it is the heating mode; if the port is disconnected, it is the cooling mode

 

 CN44

Water flow detection (fault code of the main unit E9) is only valid for the main unit but invalid for subordinate units.

             1) Main unit: if abnormal water flow occurs , the main unit board and the wired controller will display fault code E9.
             2) Subordinate unit: (water flow detection will not be done).

CN21

The alarm signal output of the unit(ON/OFF signal)

CN19

Auxiliary electric heater

 Attention: the control port value of auxiliary electric heater actually detected is ON/OFF but not 220-230V control 
power supply, so special attention should be paid when installing the auxiliary  electric  heater. Attention!
Under heating mode, when the main unit board detects total water outlet temperature to be lower than 45

℃,

the 

switch will be closed, and the auxiliary electric heater will begin to work; when the total water outlet temperature is 
higher than 50

℃,

the switch will be opened, and the auxiliary electric heater will stop working.

CN2

Pump2 signal switch,functional equivalence CN1

.

CN1

PUMP1

  Attention: the control port value of the pump actually detected is ON/OFF but not 220-230V control power supply

so 

  special attention should be paid when installing the pump.
1

After receiving start-up instruction, the pump will be started up instantly, and will maintain start-up state always in the

      process of operation.
2

In case of refrigerating or heating shutdown, the pump will be shut down 2 minutes after all modules stop operating.

3

In case of shutdown under the pump mode, the pump can be directly shut down.

CN30

Input of three-phase four-wire power supply (fault code E1)

Three phases A, B and C of power supply should exist simultaneously, and the difference of phase angle should be 
120º among them. If the conditions are not met, fault of phase sequence or phase lack may occur, and fault code will 
be displayed. When the power supply returns to normal condition, fault is removed. Attention: phase lace and phase 
dislocation of power supply are detected only in the early period after the power supply is connected, and they are not
 detected while the unit is in operation.

S5

1)The cooling water temperature of the conventional cooling water/ cooling water temperature selection (dial code S5-1) 

         host is valid,and the master slave machine needs a unified code.
       2)Remote control function selection(dial code S5-4)host effective
       3)Pump control units selection(dial code S5-3)

ENC2

Outdoor unit capacity code

ENC1

When the address is 0, it serves as the main unit

   When the address is 1,2,3……F, it serves as the subordinate unit 1,2,3……15.
Each Modular part of Modular unit has the same electric control function, and the main unit and subordinate units can 
be set through address code on the electric control board. The address code 0 #is provided as the main unit. The 
priority of being the main unit is given to the unit with digital
compressor, and other addresses are subordinate units. Only the unit is chosen as the main unit, its electric control 
can activate such functions asdirect communication with the wired controller, refrigerating and heating capability 
adjustment, pump control, auxiliary electric heater control, total effluent temperature detection and water flowswitch 
detection.

26

CN44

Remote control port(ON/OFF signal,effect on NO.0 unit)

Summary of Contents for SCV-xxEA







































Reviews: