SCS PTC-IIex Manual Download Page 3 | Manualshive

Page: 3 / 220

background image

Special Communications Systems Model PTC-IIex

Federal Communications Commission (FCC) Statement

This equipment has been tested by a FCC accredited testing facility and found to comply
with the limits for Class B Digital Device, persuant to Part 15 of the FCC rules. These rules
are designed to provide reasonable protection against harmful interference in a residential
installation.

Operation is subject to the following two conditions: 1) This device may not cause harmful
interference, and 2) this device must accept any interference received including interference
that may cause undesired operation.

This device is exempt from these rules in any transportation vehicle including motor
vehicle and aircraft as per Part 15.103 (a).

Any changes or modifications to this equipment may void the users authority to operate this
equipment.

For further information, please contact:

Farallon Electronics
2346 B Marinship Way
Sausalito, CA 94965 U.S.A.
+415 331 1924
+415 331 2063 fax

[email protected]

http://www.farallon.us

«
1
2
3
4
5
...
»

Summary of Contents for PTC-IIex





























































































































































































































Reviews:

No comments

Related manuals for PTC-IIex

Brand: Hayes Microcomputer Products Pages: 35

Brand: Sigrand Pages: 42

Brand: ARC Pages: 24

Brand: Siemens Pages: 25

Brand: Siemens Pages: 48

Brand: Siemens Pages: 79

Brand: Sagem Pages: 36

Brand: TP-Link Pages: 24

Brand: MikroTik Pages: 9

Donatello Memory ISDN Modem

Brand: Digicom Pages: 1

Brand: Digi Pages: 3

Connect WAN 3G IA

Brand: Digi Pages: 1

Brand: Digi Pages: 866

Brand: Ebyte Pages: 11

Brand: Ebyte Pages: 20

Brand: Ebyte Pages: 18

Brand: Ebyte Pages: 25

Brand: Technicolor Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands