SCS PTC-IIex Manual Download Page 17

Page: 17 / 220

1. Introduction

SCS

cannot provide support for them. If you have problems or questions concerning the

programs, please contact the author directly. Table 1.1 below gives you an overview on the
software available for specific applications.

Modes

Special Support for

Program

Text

Picture modes

PACT

HF-email

Amateur-mo

des

Packet-Rad

Hostmode

TRX-control

Firmw.-Upd

ate

Audio-modes

NAVT

Operating-

System

Airmail

WIN

Alpha

WIN

Easyterm EZT3271

WIN

EasyTransfer

WIN

EasyUpdate

WIN

GSH-PC

DOS

JVComm32

WIN

JVFAX

DOS

Kptc

Linux

Mscan Meteo Fax

WIN

Mscan Meteo Pro

WIN

Mscan SSTV

WIN

Mscan for DOS

DOS

NCWinPTC

WIN

Paxon

WIN

PlusTerm

DOS

RCKRtty

WIN

Simple

WIN

Simple32

WIN

Update

Linux

WinUpdate

WIN

XPWin

WIN

Table 1.1: List of programs

Agenda:

Special and comfortable support provided.

Possible, but no special support provided.

Not possible with this software.

•

We are frequently asked “What is the best program for the PTC-IIex?”. This question
cannot be answered easily as it is similar to someone asking “What is the best car?” or

Summary of Contents for PTC-IIex




























































































































































































































Search results

Summary of Contents for PTC-IIex

Reviews:

Related manuals for PTC-IIex

Brands by name

Popular brands

SCS PTC-IIex, Manual

Search results

Summary of Contents for PTC-IIex

Reviews:

Related manuals for PTC-IIex

Brands by name

Popular brands