Scientific Atlanta WebSTAR DPW941 User Manual Download Page 11

Page: 11 / 60

WebSTAR™ Model DPW941™ Wireless Ethernet Adapter User’s Guide

Bottom View

Mounting hole—

Use the mounting hole to install the device on wall or cabinet

surfaces using a roundhead screw.

Air vents—

These vents provide ventilation to the DPW941.

Mounting

Hole

T11447

Air Vents

Rear View

Ethernet port—

This port connects the supplied RJ-45 plug and cable.

DC IN socket—

This socket connects the power adapter plug.

Reset button—

Press this button for more than 5 seconds to load the default

values. In Ethernet adapter mode, press this button for less than 5 seconds to
connect to the first saved wireless connection in the profile table.

T11448

Ethernet

Port

Reset

Button

DC IN Socket

Summary of Contents for WebSTAR DPW941





























































Search results

Summary of Contents for WebSTAR DPW941

Reviews:

Related manuals for WebSTAR DPW941

Brands by name

Popular brands

Scientific Atlanta WebSTAR DPW941, User Manual

Search results

Summary of Contents for WebSTAR DPW941

Reviews:

Related manuals for WebSTAR DPW941

Brands by name

Popular brands